Universal Robots UR5/CB3

To Next Page

To Previous Page

9.2 Disclaimer

every care that the contents of this manual are precise and correct, but takes no responsibility

for any errors or missing information.

UR5/e-Series I-52 Version 3.11

Main Page

Default Chapter5
- Table of Contents5
Preface11
- What Do the Boxes Contain11
- Important Safety Notice11
- How to Read this Manual12
- Where to Find more Information12
I Hardware Installation Manual13
1 Safety15
- Introduction15
- Validity and Responsibility15
- Limitation of Liability16
- Warning Symbols in this Manual16
- General Warnings and Cautions17
- Intended Use20
- Risk Assessment20
- Emergency Stop22
- Movement with and Without Drive Power22
2 Safety-Related Functions and Interfaces23
- Introduction23
- Stopping Times of the Safety System24
- Limiting Safety-Related Functions24
- Safety Modes25
- Safety-Related Electrical Interfaces27
  - Safety-Related Electrical Inputs27
  - Safety-Related Electrical Outputs28
3 Transportation31
4 Mechanical Interface33
- Introduction33
- Workspace of the Robot33
- Mounting34
- Maximum Payload37
5 Electrical Interface39
- Introduction39
- Electrical Warnings and Cautions40
- Controller I/O41
- Common Specifications for All Digital I/O41
- Safety I/O41
6 Maintenance and Repair57
- Safety Instructions58
7 Disposal and Environment59
8 Certifications61
- Third Party Certification61
- Supplier Third Party Certification62
- Manufacturer Test Certification62
- Declarations According to EU Directives62
9 Warranties63
- Product Warranty63
- Disclaimer64
A Stopping Time and Stopping Distance65
- Stop Category 0 Stopping Distances and Times66
B Declarations and Certificates67
- EU Declaration of Incorporation in Accordance with ISO/IEC 17050-1:201068
- Safety System Certificate69
- TUV Rheinland70
- China Rohs71
- KCC Safety72
- Environmental Test Certificate73
- EMC Test Certificate74
- Cleanroom Test Certificates76
C Applied Standards77
D Technical Specifications85
E Safety Functions Tables87
- Table87
- Polyscope Manual93
10 Safety Configuration95
- Introduction95
- Changing the Safety Configuration96
- Safety Synchronization and Errors97
- Tolerances98
- Safety Checksum98
- Safety Modes98
- Freedrive Mode99
  - Backdrive99
- Password Lock100
- Apply100
- General Limits101
- Joint Limits103
- Boundaries104
- Safety I/O110
  - Input Signals110
  - Output Signals112
11 Begin Programming115
- Introduction115
- Getting Started115
- Polyscope Programming Interface118
- Welcome Screen120
- Initialization Screen121
12 On-Screen Editors123
- On-Screen Expression Editor123
- Pose Editor Screen126
13 Robot Control127
- Move Tab127
- Automove Tab130
- Installation Load/Save132
- Installation TCP Configuration133
- Installation Mounting136
- Installation I/O Setup137
- Installation Safety138
- Installation Variables139
- Installation MODBUS Client I/O Setup140
- Installation Features143
- Conveyor Tracking Setup149
- Smooth Transition between Safety Modes149
  - Adjusting Acceleration/Deceleration Settings150
- Installation Default Program150
- Log Tab151
  - Saving Error Reports152
- Load Screen152
- Run Tab155
14 Programming157
- New Program157
- Program Tab158
  - Program Tree158
  - Program Execution Indication159
  - Search Button159
  - Undo/Redo Buttons159
  - Program Dashboard160
  - Variables160
  - Command: Move161
  - Command: Fixed Waypoint164
  - Command: Relative Waypoint169
  - Command: Variable Waypoint170
- Command: Direction170
- Command: until171
- Command: Wait173
- Command: Set173
- Command: Popup174
- Command: Halt175
- Command: Comment175
- Command: Folder176
- Command: Loop176
- Command: if177
- Command: Subprogram178
- Command: Assignment179
- Command: Script180
- Command: Event181
- Command: Thread182
- Command: Switch182
  - Timer183
- Command: Pattern184
- Command: Force185
- Command: Pallet188
- Command: Seek189
- Command: Conveyor Tracking192
- Command: Suppress193
- Graphics Tab193
- Structure Tab194
- Variables Tab195
- Command: Variables Initialization196
15 Setup Screen197
- Language and Units198
- Update Robot199
- Set Password200
- Calibrate Screen201
- Setup Network201
- Set Time202
- Urcaps Setup203
- EUROMAP 67 Interface III-1205
18 Gui213
- EUROMAP 67 Program Template213
- I/O Overview and Troubleshooting214
- Program Structure Functionality216
- I/O Action and Wait221
19 Installing and Uninstalling the Interface III-19223
- Installing223
- Uninstalling224
20 Electrical Characteristics III-21225
- MAF Light Guard Interface225
- Emergency Stop, Safety Devices and MAF Signals225
- Digital Inputs226
- Digital Outputs228

Universal Robots UR5/CB3 - Disclaimer

Table of Contents

Related product manuals