YASKAWA E7 Drive - Page 193

Index - 1
A
A. TUNE.................................................................. 3-7, 3-14
AC Reactor ....................................................................... E-4
Accel/Decel
Parameters .................................................................A-7
Switch Frequency .................................. 5-14, 5-15, A-7
Time .........................................................................5-14
Acceleration
Stall Prevention Level during ....................... 6-16, A-20
Time................................................................ 5-14, A-7
Troubleshooting............................. 6-5, 6-10, 6-12, 6-16
Access Level ................................................................... A-2
ADV .........................................................................3-7, 3-13
Alarm Displays & Processing............................................6-8
ALARM Indicator .............................................................3-4
Altitude ............................................................................ C-4
Ambient Temperature – See Temperature
Analog Inputs
Bias................................................................ 5-16, A-16
Connection Diagram.................................................2-16
Control Circuit Terminals.........................................2-13
Gain ............................................................... 5-16, A-15
Parameters ...............................................................A-16
Troubleshooting....................................................... 6-15
Analog Outputs
Bias............................................................... A-17, A-18
Connection Diagram................................................ 2-16
Control Circuit Terminals........................................ 2-13
Gain ........................................................................ A-17
Parameters .................................................... A-17, A-18
APOGEE ..................................................... iii, iv, A-18, D-1
ASIC Faults ...................................................................... 6-3
AUTO
Key .............................................................................3-3
Mode...........................................................................3-3
REF Indicator ..................................................... 3-4, 3-5
SEQ Indicator .................................................... 3-4, 3-5
Auto Restart.....................................................................5-18
Count Reset ..............................................................5-19
Faults Covered..........................................................5-19
Max. Restart Time After Fault ................................5-18
Number of Attempts.................................................5-18
Auto-Tuning
Fault Displays and Processing..................................6-12
How to ......................................................................5-26
Line-to-Line Resistance .................................5-26, A-11
Menu..................................................................3-7, 3-14
Motor Rated Current .............................................A-25
Motor Rated Power .................................................A-25
B
Base Block
After Fault................................................................ 5-18
Circuit Fault ............................................................... 6-2
Minimum Time ......................................................... 5-6
Basic Programming...............................................5-1 to 5-26
Baud Rate .........................................................6-8, D-2, D-4
Bias Adjustments ...............................5-16, 5-17, A-16, A-18
Braking
DC Injection – See DC Injection Braking
High-Slip................................................................. A-23
Branch Short Circuit Protection................................ E-2, E-3
C
Cable Length...................................................................2-11
Capacitors – See DC Bus Capacitors
Capacity, Rated Output ............................................C-2, C-3
Capacity Related Parameters .......................................... B-1
Carrier Frequency
Error......................................................................... 6-11
Lower Limit ............................................................. A-8
Parameters................................................................. A-8
Proportional Gain ......................................................A-8
Selection ....................................................................A-8
Upper limit ............................................................... A-8
Vs. Cable Length ..................................................... 2-11
Characteristic Frequency – See Oscillation
Charge Indicator (LED) .......................... i, 1-6, 2-2, 4-5, C-4
Circuit Breakers ................................................2-9, E-2, E-3
Clearances – See Installation, Physical
Coast to Stop ..................................................................... 5-5
Coast w/Timer................................................................... 5-6
Com OPT Setup Parameters............................................A-11
Communications – Also see Modbus Communications and
Serial Communications
Errors (CPF)............................................. 6-2 to 6-4, 6-8
Parameters............................................................... A-18
Component Names.....................................................1-5, 1-6
Connections
Preventive Maintenance............................................. 7-3
Connectors
Inspection................................................................... 7-2
Sizing ............................................................... 2-3 to 2-7
Contactors
Magnetic ...................................................................E-4
Soft Charge – See Soft Charge Contactor
Control
Characteristics............................................................C-4