What to do if YASKAWA Controller shows Option Card External Fault?
If your YASKAWA Controller is showing an Option Card External Fault, it means an external fault signal was received from the PLC or there's a problem with the PLC program. To resolve this: 1. Remove the source of the external fault. 2. Reset the external fault input from the PLC. Also, check the PLC program for any issues.
Why does my YASKAWA SI-EP3 show Option Fault?
If the YASKAWA Controller displays an Option Fault, it means an option of the same type is already installed in option port CN5-A, CN5-B, or CN5-C. To fix this, connect the option to the correct option port.
What to do if YASKAWA SI-EP3 Controller shows Option Card Connection Error (CN5-A)?
If a YASKAWA Controller displays an Option Card Connection Error (CN5-A), it means the option card connection to port CN5-A is faulty. To resolve this: 1. Turn off the power. 2. Check if the option is properly plugged into the option port. 3. If the fault continues, replace the option.
What to do if YASKAWA Controller displays Option Card Error (CN5-A)?
If your YASKAWA Controller displays an Option Card Error (CN5-A), it signifies a fault in the option. To address this: 1. De-energize the drive. 2. Ensure the option is correctly connected to the connector. 3. If the problem persists, replace the option.
How to resolve Option Fault (CN5-B) on YASKAWA SI-EP3?
If the YASKAWA Controller shows an Option Fault (CN5-B) and the option card installed into port CN5-A is incompatible with the drive, connect the option to the correct option port. Use connector CN5-B when connecting DO-A3, AO-A3, or two PG options. Use connector CN5-C when connecting only one PG option.
What causes Option Card Connection Error (CN5-A) on YASKAWA SI-EP3 Controller?
If your YASKAWA Controller displays an Option Card Connection Error (CN5-A), it means that the option card installed into port CN5-A is incompatible with the drive. Connect the option to the correct option port. Note that PG option cards are supported by option ports CN5-B and CN5-C only.
How do I fix Option Fault (CN5-C) on a YASKAWA SI-EP3 Controller?
If the YASKAWA Controller displays an Option Fault (CN5-C), it indicates that the option card installed into port CN5-C is incompatible with the drive. To resolve this, connect the option to the correct option port. Keep in mind that AI-A3, DI-A3, and communication options are not supported by option port CN5-C.
How to fix Option Card Connection Error (CN5-A) on YASKAWA SI-EP3?
If your YASKAWA Controller shows an Option Card Connection Error (CN5-A), it could be due to a faulty connection of the option card to port CN5-A. To resolve this: 1. Turn off the power. 2. Check if the option is properly plugged into the option port. 3. If the fault continues to occur, replace the option.
What causes Option Card Fault (CN5-A) on YASKAWA SI-EP3?
If your YASKAWA Controller displays an Option Card Fault (CN5-A), it means the option connected to option port CN5-A was changed during run. To fix this, de-energize the drive and plug the option into the drive according to Installation Procedure.
Why does YASKAWA SI-EP3 Controller show Option Card Connection Error (CN5-A)?
If your YASKAWA Controller displays an Option Card Connection Error (CN5-A), the installed option card might be incompatible with the drive. Connect the option to the correct option port. Note that PG option cards are supported by option ports CN5-B and CN5-C only.
Lists available manuals for the PROFINET option.
Defines abbreviations and technical terms used throughout the manual.
Lists registered trademarks associated with the product and technology.
Explains safety conventions, hazard symbols, and their meanings.
Provides essential general precautions for safe operation and installation.
Lists YASKAWA AC Drive models compatible with the SI-EP3 PROFINET option.
Details the specific procedure for installing the PROFINET option on a GA500 drive.
Lists all items included in the PROFINET option package.
Lists the necessary tools required for the installation process.
Identifies and illustrates the physical components of the PROFINET option.
Describes the RJ45 connectors used for network communication.
Explains the status indicators (LEDs) on the PROFINET option.
Details the operational states indicated by the option's LEDs (MS and NS).
Explains the diagnostic LED sequence performed upon drive power-up.
Provides critical safety warnings and precautions before starting installation.
Highlights precautions to prevent equipment damage, especially ESD.
Guides on installing and wiring options for different drive models.
Details the installation procedure for 1000-series YASKAWA AC Drives.
Step-by-step instructions for physically installing the PROFINET option.
Instructions for attaching the LED label to the drive's front cover during Procedure A.
Guides on inserting the PROFINET option card into the drive connector.
Explains how to connect the provided ground wire to the drive and option.
Provides examples for routing wiring to ensure proper enclosure fit.
Instructions for connecting the PROFINET Cat 5e cable during Procedure A.
Explains using the second port for daisy-chaining multiple drives.
Steps to reattach the drive's front covers and keypad after installation.
Details the installation procedure for GA700 and GA800 YASKAWA AC Drives.
Instructions for attaching the LED label to the drive's front cover during Procedure B.
Steps to remove the drive's front cover and keypad for installation.
Instructions on how to carefully remove the LED Status Ring board.
Guides on inserting the PROFINET option card into the drive connector for Procedure B.
Instructions for connecting the PROFINET Cat 5e cable during Procedure B.
Instructions for reattaching the LED Status Ring board after wiring.
Steps to reattach the drive's front cover and keypad after installation.
Details the specifications for PROFINET dedicated communication cables.
Illustrates the physical connection diagram for the PROFINET option.
Explains network topology options like star and ring for PROFINET.
Information on obtaining GSD files for network implementation.
Lists parameters essential for configuring the drive with the PROFINET option.
Introduces the communication profile between the PROFINET I/O network and the option.
Describes the PROFIdrive profile and data words for communication.
Details the bits, names, values, and descriptions of the PROFIdrive Control Word.
Details the bits, names, values, and descriptions of the PROFIdrive Status Word.
Describes Yaskawa-specific control and status word contents for the option.
Displays drive and I/O status, and identifying information for the option.
Shows PROFINET protocol information and allows station name modification.
Displays network traffic status and the status of open I/O connections.
Explains the function of various network monitor parameters.
Allows monitoring of selected signals via a graphical chart interface.
Allows configuration of email notifications for fault and alarm conditions.
Step-by-step guide to setting up conditional email alerts for the option.
Enables reading and writing drive parameters via the web interface.
Configures web page behavior, security, and password settings.
Details how to log in to the web interface and manage security access.
Provides instructions for changing the web page access password.
Configures data update time for web page content refresh.
Configures the email server IP address and port for alert notifications.
Lists drive-side error codes, causes, and possible corrective actions.
Describes bUS and EF0 faults, and initial troubleshooting checks.
Details the EF0 fault, its alarm trigger, and solutions.
Describes connection errors related to the CN5-A port and troubleshooting steps.
Lists faults specific to the CN5-B option port and their causes.
Lists faults specific to the CN5-C option port and their causes.
Explains drive monitor parameters for tracking option fault status.
Details the compatibility of various option cards with drive connection ports.
Explains the meaning and significance of the CE mark for European commerce.
States the option's compliance with European EMC guidelines and standards.
Lists installation conditions required for maintaining EMC guideline compliance.
Illustrates CE compliant installation for various option models.
Shows the CE compliant installation procedure specific to the GA500 drive.
Provides detailed technical specifications for the SI-EP3 PROFINET option.
Provides guidelines for the proper disposal of the product and packaging.
Explains the WEEE directive concerning the recycling of electrical and electronic equipment.
Lists revision dates, numbers, and content changes for the manual.
General| Brand | YASKAWA |
|---|---|
| Model | SI-EP3 |
| Category | Controller |
| Language | English |
To Next Page
