YASKAWA E7 Drive - Page 200

Index - 8
Programming
Basic..............................................................5-1 to 5-26
Error (OPE) ............................................................. 6-11
Menu ................................................................3-7, 3-13
Proportional Gain (PI).............................................. 5-9
Protective
Functions.................................................................. C-4
Structure ................................................................... C-4
PWM Frequency — see Carrier Frequency
Q
QUICK – See Quick Setting Menu
Quick Setting Menu ....................................................... 3-12
R
RAM...............................................................................D-11
Ramp to Stop .................................................................... 5-5
Rated Current, Motor .......................... 4-6, 5-16, 6-12, A-11
Rdy – See Ready Display
Reactors, Preventive Maintenance ................................... 7-3
READ ..............................................................................5-24
Ready Display ..................................................................3-2
Receiving ......................................................................... 1-3
REF Indicator ...........................................................3-4, 3-5
Reference Limits (Also see Frequency) ...... 5-15, 6-19, A-9
Reference Selection
AUTO........................................................................ 3-3
HAND .......................................................................3-4
Reference Source.............................................. 5-2, 5-3, A-4
Relays, Preventive Maintenance ...................................... 7-3
Replacement Parts – Also see Spare Parts Ordering..............
.................................................................. Inside Back Cover
RESET Key – See SHIFT/RESET Key
Resistance, Motor Line-to-Line .......................... 5-26, A-11
Resonance....................................................................... 5-15
REV Indicator .................................................................3-4
Reverse Operation ....................................................5-6, A-4
Prohibiting............................................... 5-6, 6-16, A-4
Reverse Run/Stop command .........................2-13, 2-16, A-4
Ride-thru, Momentary Power Loss . 5-17 to 5-19, A-19, C-4
"Right Arrow" Key – See SHIFT/RESET Key
RS-485/422 .......................................................................5-4
Communication Wiring.............................................D-3
Control Circuit Terminals ....................................... 2-13
Parameters ...............................................................A-18
Terminating Resistance ...................................2-14, D-3
RTS Control Selection....................................................A-18
Run Command
During Program ........................................................ A-4
External, Troubleshooting ....................................... 6-15
Selection ...................................... 3-3, 3-5, 4-6, 5-3, A-4
Source ........................................................................ 5-3
RUN Indicator................................................................... 3-6
Running
Signal ....................................................................... 2-13
Stall Prevention during ............................................A-20
S
Scaling Display
Digital Operator...................................................... A-23
PI Setpoint ....................................................... 5-12, A-6
S-Curve Characteristic
at Accel End...............................................................A-7
at Accel Start............................................................ A-7
Search Operation Voltage Limit....................................... A-7
SEQ............................................................................ 3-4, 3-5
Sequence Parameters ....................................................... A-4
Serial Communications - See also Modbus Communications
Address ..................................................................... D-4
Baud Rate ..........................................................6-8, D-4
Drive Node Address ..................................................D-4
Parameters ...................................................... A-18, D-4
Run Command...........................................................5-4
Self-Diagnosis Function ..........................................D-13
Serial Number................................................................... 1-3
Setpoint (PI Function)..................................................... 5-12
Boost Setting....................................................5-13, A-6
Display Scaling................................................ 5-12, A-6
Selection .......................................................... 5-12, A-6
Value ................................................................ 5-12, A-6
SHIFT/RESET Key ................................................. 3-3, 5-19
Shield Wire Grounding ..........................................2-13, 2-17
Shipping Damage.............................................................. 1-3
Short Circuit Protection, Branch............................... E-2, E-3
Sinking/Sourcing Mode ................................2-13, 2-15, 2-16
Skip Frequency –– See Jump Frequency and Frequency
Limits
Slave – See Modbus Communication Configuration
Sleep Function – See PI Function, Sleep
Snooze Function – See PI Function, Snooze
Soft Charge Contactor
Alarm .......................................................................6-10
Checking.................................................................. 6-21
Fault ...........................................................................6-7
Preventive Maintenance ............................................ 7-3