YASKAWA GPD-506V - Page 163

I-1
- A -
Accel Function LED...........4-2, 4-3
Acceleration :
Stall Prev. Level During ..... 5-53
Time 1 ................................. 5-3
Time 2 ................................. 5-3
Analog Monitor Gain ............. 5-27
Analog Output, Multi-func.
(Term. AM-AC) .............. 5-27
At Set Speed, Stall Prev.
Level ............................. 5-54
Auto Analog Input Sel. ..................
......................................5-15, 5-16
Auto Restart Attempts ............ 5-5
Auto Restart, Fault Contact
Selection During ............. 5-5
Auxiliary Input and Output
Power Option Devices ...1-11
- B -
Base Block, External ............. 5-33
Basic Programming ................ 4-5
Bias, Freq. Ref. ..................... 5-13
BPS Selection, Modbus ........ 5-23
Braking, DC Injection :
Current ................................. 5-8
Time at Start ........................ 5-8
Time at Stop ........................ 5-8
Braking, Dynamic ................. A6-1
- C -
Carrier Frequency ................... 5-6
Changeover, Local/Remote ... 5-21
Communication Error, Modbus
Stop Method at ... 6-2, A1-13
Compensation, Slip .............. 5-51
Conformance to European
EMC Directive ............... 1-11
Control Circuit Wiring ............. 1-8
Critical Freq. Rejection ............ 5-7
CT/VT Selection .................. A1-14
Current, DC Inj. Braking .......... 5-8
Current, Motor No-load ........ 5-57
- D -
Deactivation Time, Momentary
Power Loss Ride-thru ... 5-26
Decel Function LED ........ 4-2, 4-3
Deceleration :
Stall Prevention During ...... 5-53
Time 1 ................................. 5-3
Time 2 ................................. 5-3
Delay Time :
Feedback Loss Detection
(PID) .......................... 5-47
Derivative Time (PID) ........... 5-48
Detection, Fdbk. Loss (PID) .. 5-47
Det’n, Modbus Time Out .......A1-9
Detection Level :
Input Phase Loss ............... 5-63
Feedback Loss (PID) ......... 5-47
Overtorque (OL3) .............. 5-43
Detection Time :
Overtorque (OL3) .............. 5-43
Diagnostics — see
Troubleshooting
Digital Operator ............... 2-2, 4-1
Digital Operator Display
Selection ......................... 5-9
Dimensions .......................... A5-1
Displays, Monitor ................... 4-6
“Down Arrow” Key ................. 4-1
DSPL key ................................ 4-1
Dynamic Braking Connections ......
...............................................A6-1
- E -
Elapsed Timer 1 .................... A1-9
Elapsed Timer 2 .................... A1-9
Elapsed Timer Selection ....... A1-9
EMC Directive, European,
Conformance to ............ 1-11
Energy Saving :
Gain K2 .............................. 5-11
Selection ............................ 5-11
Tuning ............................... 5-12
Volt. Lower Limit at 6Hz .... 5-11
Volt. Lower Limit at 60Hz .. 5-11
Enclosure ............................. A5-1
ENTER Key ............................. 4-1
Environment ................. 1-1, A2-3
European EMC Directive,
Conformance to ............ 1-12
- F -
Fault Contact Selection
During Auto Restart ........ 5-5
Fbias Quick Start
Displays .................. 4-2, 4-3
Feedback Calibration
Gain (PID) .................... 5-47
Feedback Loss (PID) :
Detection Selection ............ 5-47
Detection Delay Time ......... 5-47
Detection Level .................. 5-47
Fgain Quick Start
Displays .................. 4-2, 4-3
FLA Quick Start
Displays .................. 4-2, 4-4
Fout Quick Start Displays ....... 4-2
Display Selection ................. 5-9
Fref Quick Start Displays ........ 4-2
Frequency :
Base .................................. 5-61
Carrier ................................. 5-6
Detection ........................... 5-42
Max. Output ....................... 5-61
Meter ................................. 5-27
Min. Output ....................... 5-61
Min. Output Voltage ........... 5-61
Output ................................. 4-2
Prohibited ............................ 5-7
Range ................................ 5-17
Ref. Retention (Up/Down
& Sample/Hold) ......... 5-19
Frequency Detection Multi-
function Output ............ 5-42
Frequency Reference 1 ......... 5-31
Frequency Reference 2 ......... 5-31
Frequency Reference 3 ......... 5-31
Frequency Reference 4 ......... 5-31
INDEX