YASKAWA GPD-506V - Page 164

I-2
Frequency Reference :
Bias ................................... 5-13
Gain ................................... 5-13
Jog ........................... 5-20, 5-31
Limit, Lower ...................... 5-17
Limit, Upper ...................... 5-17
Loss Detection, Operation
Method for ................. 5-18
Resolution, Modbus .......... 5-23
Retention ........................... 5-19
Setting Method From
Digital Operator ........... 2-2
Function LEDs ................. 4-1, 4-2
- G -
Gain :
Analog Monitor .................. 5-27
Feedback Calib. (PID) ........ 5-47
Frequency Reference ......... 5-13
Proportional (PID) ............. 5-47
Torque Compensation ........ 5-59
Gain K2, Energy Saving ........ 5-11
Grounding .............................. 1-9
- I -
Initialize Parameters ............. 5-50
Input Phase Loss Detection :
Delay Time (SPi) ................ 5-63
Level .................................. 5-63
Input Selection
Auto Analog ....................... 5-15
Manual Analog ................... 5-15
Multi-function Contact ....... 5-28
Input Voltage ........................ A2-1
Inputs :
Analog ............................... 1-15
Frequency Reference ......... 1-15
Inspection (Receiving) ............ 1-1
Installation .............................. 1-1
Integral Time (PID) ............... 5-48
Integral Value Limit (PID) ..... 5-48
Integral Value Reset (PID) .... 5-48
Inverse PID ........................... 5-46
Iout Function LED ................... 4-2
Iron Loss .............................. 5-59
- J -
Jog Frequency Ref. ..... 5-20, 5-29
- K -
Keypad — see Digital
Operator
kVA Selection (n115 ) ........... A3-1
- L -
Lag Filter Time, Output (PID) 5-47
LEDs, Function ................ 4-1, 4-2
LEDs, Status Indicator ............ 4-1
Limit, Integral Value (PID) .... 5-48
Line-to-Line Res., Motor ...... 5-59
Local/Remote Changeover .... 5-21
LOCAL/REMOTE Key .............. 4-1
LOC./REM. Key Func. ...........A1-2
Lower Limit, Freq. Ref. ......... 5-17
- M -
Main Circuit :
Block Diagrams .............1-6, 1-7
Terminals ..................... 1-3, 1-5
Input/Output Wiring ............. 1-2
Maintenance ........................... 6-5
Manual Analog Input Sel. ..... 5-15
Max. Output Frequency ........ 5-61
Max. Voltage ......................... 5-61
Max. Volt. Output Freq. ......... 5-61
Mechanical resonance — see
Critical Frequency Rejection
Mid. Frequency Voltage ........ 5-61
Min. Base Block Time ........... 5-33
Min. Output Frequency ......... 5-61
Min. Output Volt. Freq. ......... 5-61
Miscellaneous Protective
Features ........................ 5-25
Modbus :
BPS Selection .................... 5-23
Freq. Resolution ................ 5-23
Parity Selection ................. 5-23
Stop Method at Comm.
Error ........................ A1-13
Time Out Detection .......... A1-13
Slave Address .................... 5-23
Mode Selection ..................... 5-22
Model Numbers, Drive ..................
.....................................A2-1, A5-1
Momentary Power Loss
Ride-through Selection .. 5-26
Monitor Displays .................... 4-6
Motor :
Iron Loss ........................... 5-59
Line-to-Line Resistance ..... 5-59
No-load Current ................. 5-57
Overload Prot. Selection .... 5-57
Rated Current (FLA) ............ 4-4
Rated Voltage .................... 5-62
Switching — see Speed
Search
Wiring .................................. 1-2
Mounting :
Clearances ........................... 1-1
Dimensions ....................... A5-1
European EMC
Conformance ................1-11
Location ..................... 1-1, A2-3
Multi-function Analog Output
(AM-AC) ....................... 5-27
Multi-func. Contact Input
Selection ....................... 5-28
Multi-func. Contact Output
Selection ....................... 5-41
Multi-step Speed .................. 5-31
INDEX – Continued