Modes
3-7
Drive Mode
Drive mode is the mode in which the Inverter can be operated. The following monitor displays are possible in
drive mode: The frequency reference, output frequency, output current, and output voltage, as well as fault
information and the fault history.
When b1-01 (Reference selection) is set to 0, the frequency can be changed from the frequency setting display.
Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will be
written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing the
setting.
Example Operations
Key operations in drive mode are shown in the following figure.
Fig 3.4 Operations in Drive Mode
Monitor Display Frequency Setting DisplayMode Selection
Display
Display at Startup
The fault name will be
displayed if the DATA/ENTER
Key is pressed while a constant
is being displayed for which a
fault code is being displayed.
The Frequency Setting
Display will not be
displayed when using an
analog reference.
ⲥ㾚
'5,9(
0(18
(6&
'$7$
(17(5
乥⥛ᣛҸ
'5,9(
8
+]
乥⥛ᣛҸ
'5,9(
8 +]
0(18
0(18
0(18
0(18
˚
5(6(7
'$7$
(17(5
(6&
'$7$
(17(5
ᬙ䱰䆄ᔩ
'5,9(
8 2&
䕧ߎ乥⥛
'5,9(
ዄֱؐᣕ䕧ߎ乥⥛
'5,9(
ࠡᬙ䱰
'5,9('5,9(
8 2&
ࠡᬙ䱰
'5,9(
'5,9(
8 29
˚
5(6(7
(6&
$ %
$ %
䖛এᬙ䱰
'5,9( '5,9(
8
29
˚
5(6(7
(6&
8 29
Џಲ䏃䖛⬉
'$7$
(17(5
(6&
8 2&
䕧ߎ䖛⬉⌕
'$7$
(17(5
(6&
8 29
Џಲ䏃䖛⬉
'$7$
(17(5
(6&
5G\
5G\
5G\
5G\
5G\ 5G\
5G\
(6&
ⲥ㾚
'5,9(
5G\
˚
5(6(7
(6&
ⲥ㾚
'5,9(
8 +]
5G\
˚
5(6(7
(6&
5G\
5G\
ᬙ䱰䎳䏾
'5,9(
5G\
˚
5(6(7
(6&
ᬙ䱰䆄ᔩ
'5,9(
8 29
5G\
˚
5(6(7
(6&
'$7$
(17(5
8 +]
8 +]
8 29
8
+]
8
+]
乥⥛ᣛҸ
'5,9(
偅ࡼᓣ
'5,9(
*
*
*
ㅔᯧᑣᓣ
48,&.
*
*
*
催㑻ᑣᓣ
$'9
*
*
*
偠ᓣ
9(5,)<
*
*
*
㞾ᄺдᓣ
$781(
*
*
*
5G\
8 +]
'5,9(
8
ᬙ䱰䎳䏾
5G\
'5,9(
8
ᔧࠡᬙ䱰
5G\
'$7$
(17(5
To Next Page
Loading...
Need help?
General