Command Function Page
:COMMunicate:WAIT
Waits for one of the specified extended events to occur. 5-71
:COMMunicate:WAIT?
Creates the response that is returned when the specified event occurs. 5-71
CURSor Group
:CURSor?
Queries all settings related to the cursor measurement. 5-72
:CURSor:DISPlay
Turns ON/OFF the cursor or queries the current setting. 5-72
:CURSor:HORizontal?
Queries all settings related to the horizontal cursors. 5-72
:CURSor:HORizontal:BASic?
Queries all settings related to basic items of the horizontal cursors. 5-72
:CURSor:HORizontal[:BASic]:ALL
Turns ON/OFF all basic items of the horizontal cursors. 5-72
:CURSor:HORizontal[:BASic]:DV?
Queries
allsettingsrelatedtothe∆Vmeasurementofthehorizontalcursors.
5-72
:CURSor:HORizontal[:BASic]:DV:
STATe
T
urnsON/OFFthe∆Vmeasurementofthehorizontalcursorsorqueriesthe
current setting.
5-72
:CURSor:HORizontal[:BASic]:DV:
VALue?
Queries the voltage value between the horizontal cursors. 5-72
:CURSor:HORizontal[:BASic]:
LINKag
e
Turns ON/OFF the horizontal cursor link or queries the current setting. 5-72
:CURSor:HORizontal[:BASic]:
V<x>?
Queries all settings related to the horizontal cursor. 5-73
:CURSor:HORizontal[:BASic]:
V<x>:JUMP
Jumps the horizontal cursor to the center position of the zoom waveform. 5-73
:CURSor:HORizontal[:BASic]:
V<x>:POSition
Sets the horizontal cursor position or queries the current setting. 5-73
:CURSor:HORizontal[:BASic]:
V<x>:STATe
Turns ON/OFF the horizontal cursor or queries the current setting. 5-73
:CURSor:HORizontal[:BASic]:
V<x>:VALue?
Queries the voltage value at the horizontal cursor. 5-73
:CURSor:HORizontal:CALCulation?
Queries all settings related to calculation items of the horizontal cursors. 5-73
:CURSor:HORizontal:CALCulation:
ALL
Turns ON/OFF all calculation items of the horizontal cursors. 5-73
:CURSor:HORizontal:CALCulation:
DEFine<x>
Sets the equation of the calculation item of the horizontal cursor or queries
the current setting.
5-73
:CURSor:HORizontal:CALCulation:
STATe<x>
Turns ON/OFF the calculation item of the horizontal cursor or queries the
current setting.
5-73
:CURSor:HORizontal:CALCulation:
VALue<x>?
Queries the measured value of the calculation item of the horizontal cursor. 5-73
:CURSor:HORizontal:TRACe
Sets the source trace of the horizontal cursor or queries the current setting. 5-74
:CURSor:MARKer?
Queries all settings related to the marker cursors. 5-74
:CURSor:MARKer:CALCulation?
Queries all settings related to calculation items of the marker cursors. 5-74
:CURSor:MARKer:CALCulation:ALL
Turns ON/OFF all calculation items of the marker cursors. 5-74
:CURSor:MARKer:CALCulation:
DEFine<x>
Sets the equation of the calculation item of the marker cursors or queries the
current setting.
5-74
:CURSor:MARKer:CALCulation:
STATe<x>
Turns ON/OFF the calculation item of the marker cursors or queries the
current setting.
5-74
:CURSor:MARKer:CALCulation:
VALue<x>?
Queries the measured value of the calculation item of the marker cursors. 5-74
:CURSor:MARKer:CM<x>?
Queries all settings related to the marker cursor. 5-74
:CURSor:MARKer:CM<x>:ALL
Turns ON/OFF all items of the marker cursor. 5-75
:CURSor:MARKer:CM<x>:DT<x>?
Queries
allsettingsrelatedtothe∆Tmeasurementofthecursormarker
.
5-75
:CURSor:MARKer:CM<x>:DT<x>:
STATe
T
urnsON/OFFthe∆Tmeasurementofthemakercursororqueriesthe
current setting.
5-75
:CURSor:MARKer:CM<x>:DT<x>:
VALue?
Queriesthe∆Tvalueofthemarkercursor
. 5-75
:CURSor:MARKer:CM<x>:DV<x>?
Queriesallsettingsrelatedtothe∆Vmeasurementofthecursormarker
.
5-75
:CURSor:MARKer:CM<x>:DV<x>:
STATe
T
urnsON/OFFthe∆Vmeasurementofthemakercursororqueriesthe
current setting.
5-75
:CURSor:MARKer:CM<x>:DV<x>:
VALue?
Queriesthe∆Vvalueofthemarkercursor. 5-75
:CURSor:MARKer:CM<x>:JUM
P
Jumps the marker cursor to the center position of the zoom waveform. 5-75
:CURSor:MARKer:CM<x>:POSition
Sets the marker cursor position or queries the current setting. 5-75
:CURSor:MARKer:CM<x>:T?
Queries all settings related to the time measurement of the marker cursor. 5-75
:CURSor:MARKer:CM<x>:T:STATe
Turns ON/OFF the time measurement of the maker cursor or queries the
current setting.
5-76
:CURSor:MARKer:CM<x>:T:VALue?
Queries the time value at the marker cursor position. 5-76
5.1 List of Commands
To Next Page
Loading...
Need help?
General
