EasyManua.ls Logo

3Com 4510G - Page 181

3Com 4510G
1166 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
10-12
[ProviderA] interface gigabitethernet 1/0/2
[ProviderA-GigabitEthernet1/0/2] port link-type hybrid
[ProviderA-GigabitEthernet1/0/2] port hybrid vlan 1000 untagged
# Tag CVLAN 10 frames with SVLAN 1000.
[ProviderA-GigabitEthernet1/0/2] qinq vid 1000
[ProviderA-GigabitEthernet1/0/2-vid-1000] raw-vlan-id inbound 10
[ProviderA-GigabitEthernet1/0/2-vid-1000] quit
[ProviderA-GigabitEthernet1/0/2] quit
z Configure GigabitEthernet 1/0/3
# Configure GigabitEthernet 1/0/3 as a trunk port to permit frames of VLAN 1000 and VLAN 2000 to
pass through.
[ProviderA] interface gigabitethernet 1/0/3
[ProviderA-GigabitEthernet1/0/3] port link-type trunk
[Sysname-GigabitEthernet1/0/3] port trunk permit vlan 1000 2000
# Set the TPID value in the outer tag to 0x8200.
[ProviderA-GigabitEthernet1/0/3] quit
[ProviderA] qinq ethernet-type 8200
2) Configuration on Provider B
z Configure GigabitEthernet 1/0/1
# Configure GigabitEthernet 1/0/1 as a trunk port to permit frames of VLAN 1000 and VLAN 2000 to
pass through.
<ProviderB> system-view
[ProviderB] interface gigabitethernet 1/0/1
[ProviderB-GigabitEthernet1/0/1] port link-type trunk
[ProviderB-GigabitEthernet1/0/1] port trunk permit vlan 1000 2000
z Configure GigabitEthernet 1/0/2
# Configure GigabitEthernet 1/0/2 as a hybrid port to permit frames of VLAN 2000 to pass through, and
configure GigabitEthernet 1/0/2 to send packets of VLAN 2000 with tag removed.
[ProviderB] interface gigabitethernet 1/0/2
[ProviderB-GigabitEthernet1/0/2] port link-type hybrid
[ProviderB-GigabitEthernet1/0/2] port hybrid vlan 2000 untagged
# Tag CVLAN 20 frames with SVLAN 2000.
[ProviderB-GigabitEthernet1/0/2] qinq vid 2000
[ProviderB-GigabitEthernet1/0/2-vid-2000] raw-vlan-id inbound 20
# Set the TPID value in the outer tag to 0x8200.
[ProviderA-GigabitEthernet1/0/3] quit
[ProviderA] qinq ethernet-type 8200
3) Configuration on third-party devices
Configure the third-party devices between Provider A and Provider B as follows: configure the port
connecting GigabitEthernet 1/0/3 of Provider A and that connecting GigabitEthernet 1/0/1 of Provider B
to allow tagged frames of VLAN 1000 and VLAN 2000 to pass through.

Table of Contents

Related product manuals