3Com Switch 4500 Family

To Next Page

3Com Switch 4500 Family

Command Reference Guide

Switch 4500 26-Port

Switch 4500 50-Port

Switch 4500 PWR 26-Port

Switch 4500 PWR 50-Port

Product Version: V03.03.00

Manual Version:

6W101-20090811

www.3com.com

3Com Corporation

350 Campus Drive, Marlborough,

MA, USA 01752 3064

Main Page

Table of Contents6
- Default Chapter1
- 1 Login Commands8
- 2 Commands for User Control43
Configuration File Management Commands48
- Configuration File Management Commands49
- Display Current-Configuration49
- File Attribute Configuration Commands49
- Display Current-Configuration Vlan53
- Display Saved-Configuration54
- Display Startup56
- Display this57
- Reset Saved-Configuration58
- Save59
- Startup Saved-Configuration61
VLAN Configuration Commands63
- Description64
- Display Interface Vlan-Interface64
- VLAN Configuration Commands64
- Display Vlan65
- Interface Vlan-Interface67
- Name67
- Shutdown68
- Vlan69
- Display Port70
- Port70
- Port-Based VLAN Configuration Commands70
- Port Access Vlan71
- Port Hybrid Pvid Vlan72
- Port Hybrid Vlan72
- Port Link-Type73
- Port Trunk Permit Vlan74
- Port Trunk Pvid Vlan75
IP Address Configuration Commands/Ip Performance Optimization Configuration Commands76
- 1 IP Address Configuration Commands77
- 2 IP Performance Optimization Configuration Commands83
Voice VLAN Configuration Commands101
- Display Voice Vlan Error-Info102
- Display Voice Vlan Oui102
- Voice VLAN Configuration Commands102
- Display Voice Vlan Status103
- Display Vlan104
- Voice Vlan105
- Voice Vlan Aging106
- Voice Vlan Enable107
- Voice Vlan Legacy107
- Voice Vlan Mac-Address108
- Voice Vlan Mode109
- Voice Vlan Security Enable110
Port Basic Configuration Commands111
- Broadcast-Suppression112
- Port Basic Configuration Commands112
- Copy Configuration113
- Description115
- Display Brief Interface115
- Display Interface117
- Display Link-Delay121
- Display Loopback-Detection121
- Display Port Combo122
- Display Unit123
- Duplex124
- Flow-Control125
- Flow Interval126
- Giant-Frame Statistics Enable126
- Interface127
- Jumboframe Enable128
- Link-Delay128
- Loopback129
- Loopback-Detection Control Enable130
- Loopback-Detection Enable131
- Loopback-Detection Interval-Time132
- Loopback-Detection Per-Vlan Enable132
- MDI133
- Multicast-Suppression133
- Reset Counters Interface134
- Shutdown135
- Speed136
- Speed Auto137
- Unicast-Suppression137
- Virtual-Cable-Test138
Link Aggregation Configuration Commands140
- Display Link-Aggregation Interface141
- Link Aggregation Configuration Commands141
- Display Link-Aggregation Summary142
- Display Link-Aggregation Verbose143
- Display Lacp System-ID144
- Lacp Enable145
- Lacp Port-Priority145
- Lacp System-Priority146
- Link-Aggregation Group Description146
- Link-Aggregation Group Mode147
- Port Link-Aggregation Group148
- Reset Lacp Statistics149
  - Port Isolation Configuration Commands151
Port Security Commands153
- Display Mac-Address Security154
- Port Security Commands154
- Display Port-Security155
- Mac-Address Security158
- Port-Security Authorization Ignore159
- Port-Security Enable160
- Port-Security Intrusion-Mode161
- Port-Security Max-Mac-Count163
- Port-Security Ntk-Mode164
- Port-Security Oui165
- Port-Security Port-Mode166
- Port-Security Timer Disableport169
- Port-Security Trap170
For Description of the Output Information, Refer to Table 1-2.173
- Display Dldp174
- DLDP Configuration Commands174
- Dldp175
- Dldp Authentication-Mode175
- Dldp Interval177
- Dldp Reset178
- Dldp Unidirectional-Shutdown178
- Dldp Work-Mode179
- Dldp Delaydown-Timer180
Examples # Set the Delaydown Timer to 5 Seconds.182
- MAC Address Table Management Configuration Commands183
Auto Detect Configuration Commands190
- Auto Detect Configuration Commands191
- Detect-Group191
- Detect-List192
- Display Detect-Group193
- Ip Route-Static Detect-Group194
- Retry196
- Standby Detect-Group196
- Timer Loop197
- Timer Wait197
Mstp Configuration Commands199
- Active Region-Configuration201
- Check Region-Configuration201
- MSTP Configuration Commands201
- Display Stp203
- Display Stp Abnormalport206
- Display Stp Portdown207
- Display Stp Region-Configuration208
- Display Stp Root209
- Instance210
- Region-Name210
- Reset Stp211
- Revision-Level212
- Stp212
- Stp Bpdu-Protection214
- Stp Bridge-Diameter215
- Stp Compliance215
- Stp Config-Digest-Snooping217
- Stp Cost219
- Stp Dot1D-Trap220
- Stp Edged-Port221
- Stp Loop-Protection222
- Stp Max-Hops224
- Stp Mcheck224
- Stp Mode226
- Stp No-Agreement-Check226
- Stp Pathcost-Standard228
- Stp Point-To-Point229
- Stp Port Priority231
- Stp Portlog232
- Stp Portlog All232
- Stp Priority233
- Stp Region-Configuration233
- Stp Root Primary234
- Stp Root Secondary235
- Stp Root-Protection236
- Stp Tc-Protection238
- Stp Tc-Protection Threshold238
- Stp Timer Forward-Delay239
- Stp Timer Hello240
- Stp Timer Max-Age241
- Stp Timer-Factor242
- Stp Transmit-Limit243
Table of Contents246
- 1 IP Routing Table Commands248
- 2 Static Route Configuration Commands261
  - Delete Static-Routes All261
  - Ip Route-Static262
- 3 RIP Configuration Commands264
- 4 IP Routing Policy Configuration Commands284
Common Multicast Configuration Commands/Igmp Snooping Configuration Commands293
- 1 Common Multicast Configuration Commands294
- 2 IGMP Snooping Configuration Commands299
Table of Contents320
- 802.1X Configuration Commands322
- 2 Quick EAD Deployment Configuration Commands342
- 3 HABP Configuration Commands345
- 4 System Guard Configuration Commands350
Aaa Configuration Commands358
- 1 AAA Configuration Commands360
- 2 EAD Configuration Commands418
  - Security-Policy-Server418
Table of Contents420
- MAC Address Authentication Basic Function Configuration Commands421
- MAC Address Authentication Enhanced Function Configuration Commands430
Arp Configuration Commands434
- Arp Anti-Attack Valid-Check Enable435
- Arp Check Enable435
- ARP Configuration Commands435
- Arp Static436
- Arp Timer Aging437
- Display Arp437
- Display Arp Count439
- Display Arp Timer Aging440
- Gratuitous-Arp Period-Resending Enable441
- Gratuitous-Arp-Learning Enable441
- Reset Arp442
Dhcp Snooping Configuration Commands/Dhcp/Bootp Client Configuration443
- Default Chapter444
  - DHCP Relay Agent Configuration Commands444
- 2 DHCP Snooping Configuration Commands455
- 3 DHCP/BOOTP Client Configuration464
  - DHCP Client Configuration Commands464
    - Display Dhcp Client464
    - Ip Address Dhcp-Alloc465
  - BOOTP Client Configuration Commands466
    - Display Bootp Client466
    - Ip Address Bootp-Alloc467
Acl Configuration Commands468
- Acl469
- ACL Configuration Commands469
- Description470
- Display Acl471
- Display Drv Qacl_Resource472
- Display Packet-Filter473
- Display Time-Range474
- Packet-Filter475
- Packet-Filter Vlan477
- Rule (for Basic Acls)478
- Rule (for Advanced Acls)480
- Rule (for Layer 2 Acls)487
- Rule (for User-Defined Acls)490
- Rule Comment493
- Time-Range494
Qos Commands497
- Display Protocol-Priority498
- Qos Commands498
- Display Qos Cos-Local-Precedence-Map499
- Display Qos-Interface All499
- Display Qos-Interface Line-Rate502
- Display Qos-Interface Mirrored-To503
- Display Qos-Interface Traffic-Limit503
- Display Qos-Interface Traffic-Priority504
- Display Qos-Interface Traffic-Remark-Vlanid505
- Display Queue-Scheduler505
- Line-Rate506
- Priority509
- Priority Trust510
- Protocol-Priority Protocol-Type511
- Qos Cos-Local-Precedence-Map513
- Queue-Scheduler514
- Traffic-Priority519
- Traffic-Priority Vlan521
- Traffic-Remark-Vlanid522
- Wred523
Mirroring Commands525
- Display Mirroring-Group526
- Mirroring Commands526
- Mirroring-Group527
- Mirroring-Group Mirroring-Port528
- Mirroring-Group Monitor-Port529
- Mirroring-Group Reflector-Port530
- Mirroring-Group Remote-Probe Vlan531
- Mirroring-Port532
- Monitor-Port533
- Remote-Probe Vlan Enable534
Related Commands: Mirroring-Group Remote-Probe VLAN. # Configure VLAN 5 as the Remote-Probe VLAN.536
- Change Self-Unit537
- XRN Fabric Commands537
- Change Unit-ID538
- Display Ftm540
- Display Xrn-Fabric543
- Fabric Save-Unit-ID544
- Fabric-Port Enable546
- Ftm Fabric-Vlan547
- Port Link-Type Xrn-Fabric548
- Xrn-Fabric Authentication-Mode548
- Reset Ftm Statistics549
- Set Unit Name549
- Sysname550
Cluster Configuration Commands552
- Cluster Configuration Commands554
- Display Ndp554
- Ndp Configuration Commands554
- NTDP Configuration Commands559
- Cluster Configuration Commands566
- Enhanced Cluster Feature Configuration Commands598
Poe Configuration Commands/Poe Profile Configuration Commands608
- 1 Poe Configuration Commands609
- 2 Poe Profile Configuration Commands621
Snmp Configuration Commands/Rmon Configuration Commands629
- 1 Snmp Configuration Commands630
- 2 Rmon Configuration Commands659
Ntp Configuration Commands674
- Display Ntp-Service Sessions675
- NTP Configuration Commands675
- Display Ntp-Service Status677
- Display Ntp-Service Trace678
- Ntp-Service Access679
- Ntp-Service Authentication Enable680
- Ntp-Service Authentication-Keyid681
- Ntp-Service Broadcast-Client681
- Ntp-Service Broadcast-Server682
- Ntp-Service In-Interface Disable682
- Ntp-Service Max-Dynamic-Sessions683
- Ntp-Service Multicast-Client684
- Ntp-Service Multicast-Server684
- Ntp-Service Reliable Authentication-Keyid685
- Ntp-Service Source-Interface686
- Ntp-Service Unicast-Peer686
- Ntp-Service Unicast-Server687
Ssh Commands689
- Display Public-Key Local690
- SSH Commands690
- Display Public-Key Peer691
- Display Rsa Local-Key-Pair Public692
- Display Rsa Peer-Public-Key693
- Display Ssh Server694
- Display Ssh Server-Info695
- Display Ssh User-Information696
- Display Ssh2 Source-Ip696
- Display Ssh-Server Source-Ip697
- Peer-Public-Key End697
- Protocol Inbound698
- Public-Key Local Create699
- Public-Key Local Destroy700
- Public-Key Local Export Rsa701
- Public-Key Peer702
- Public-Key Peer Import Sshkey703
- Public-Key-Code Begin704
- Public-Key-Code End705
- Rsa Local-Key-Pair Create706
- Rsa Local-Key-Pair Destroy707
- Rsa Peer-Public-Key707
- Rsa Peer-Public-Key Import Sshkey708
- Ssh Authentication-Type Default709
- Ssh Client Assign710
- Ssh Client First-Time Enable711
- Ssh Server Authentication-Retries712
- Ssh Server Timeout713
- Ssh User713
- Ssh User Assign715
- Ssh User Authentication-Type716
- Ssh User Service-Type717
- Ssh2718
- Ssh2 Source-Interface719
  - Ssh2 Source-Ip720
- Ssh-Server Source-Interface720
- Ssh-Server Source-Ip721
Table of Contents723
- File System Configuration Commands724
- File Attribute Configuration Commands740
- Configuration File Backup and Restore Commands745
  - Backup Current-Configuration745
  - Restore Startup-Configuration746
Ftp and Sftp Configuration Commands748
- 1 FTP and SFTP Configuration Commands750
- 2 TFTP Configuration Commands787
Information Center Configuration Commands794
- Display Channel795
- Display Info-Center795
- Information Center Configuration Commands795
- Display Logbuffer797
- Display Logbuffer Summary799
- Display Trapbuffer799
- Info-Center Channel Name800
- Info-Center Console Channel801
- Info-Center Enable801
- Info-Center Logbuffer802
- Info-Center Loghost803
- Info-Center Loghost Source804
- Info-Center Monitor Channel804
- Info-Center Snmp Channel805
- Info-Center Source806
- Info-Center Synchronous808
- Info-Center Switch-On809
- Info-Center Timestamp810
- Info-Center Timestamp Loghost810
- Info-Center Trapbuffer811
- Reset Logbuffer812
- Reset Trapbuffer812
- Terminal Debugging813
- Terminal Logging813
- Terminal Monitor814
- Terminal Trapping814
By Default, Trap Terminal Display Is Enabled. Examples # Enable Trap Terminal Display.816
- Default Chapter818
- 2 Network Connectivity Test Commands828
  - Tracert830
- 3 Device Management Commands832
Ipv6 Configuration Commands/Ipv6 Application Configuration Commands870
- 1 Ipv6 Configuration Commands871
  - Basic Ipv6 Configuration Commands871
- 2 Ipv6 Application Configuration Commands901
- Appendix A Command Index911

Need help?

Do you have a question about the 3Com Switch 4500 Family and is the answer not in the manual?

3Com Switch 4500 Family Specifications

General

Brand	3Com
Model	Switch 4500 Family
Category	Switch
Language	English

Related product manuals

3Com Switch 4500 26-Port

396 pages

3CR17571-91 - Switch 4500 PWR

128 pages

3CR17561-91-US - Switch 4500 26PORT Managed 24 10/100 2 Gbe Stackable RJ45

128 pages

3Com Switch 4210 Series

80 pages

3Com Switch 4210 26-Port

80 pages

3Com Switch 4800G 24-Port

1246 pages

SuperStack 3 Switch 4400 Series

86 pages

3Com Baseline Switch

4 pages

Baseline Switch 2928-SFP Plus

62 pages

Baseline Switch 2952-SFP Plus

62 pages

Baseline Switch 2920-SFP Plus

62 pages

Baseline Switch 2824 3CBLUG24

8 pages

3Com Switch 4500 Family - User Manual

Table of Contents

3Com Switch 4500 Family Specifications

Related product manuals