ABB A145-M65 - Page 141

Operation Manual / 4 Product description / A130-M.. - A145-M..
Tables
© Copyright 2017 ABB. All rights reserved. HZTL4031_EN Revision F August 2017
Tables
Table1: Related documents .......................................... 3
Table2: Weights of turbochargers A130-M.. – A145-
M.. ...................................................................................... 8
Table3: Requirements for threaded rods ................ 14
Table4: Tightening torques for standard nuts....... 16
Table5: Pressure screw tightening torques............ 18
Table6: Lubricating oil pressure, oil inlet ............... 25
Table7: Lubricating oil temperature at the inlet ... 26
Table8: Lubricating oil temperature at the outlet 26
Table9: Tightening torque(86505).......................... 30
Table10: Expected replacement intervals ............... 37
Table11: Maintenance table ....................................... 40
Table12: Parameters for wet cleaning of com-
pressor ........................................................................... 44
Table13: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 47
Table14: Wet cleaning of turbines, parameters .... 48
Table15: Value table for soaking .............................. 56
Table16: Malfunctions when starting – Delayed
start-up .......................................................................... 59
Table17: Malfunctions when starting – Vibrations 59
Table18: Malfunctions when starting – Rubbing of
rotating parts................................................................ 59
Table19: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 60
Table20: Malfunctions during operation – Speed re-
duces............................................................................... 60
Table21: Malfunctions during operation – Speed in-
creases ........................................................................... 60
Table22: Malfunctions during operation – Exhaust
gas temperature too high ........................................... 61
Table23: Malfunctions during operation – Charge air
pressure too low............................................................ 61
Table24: Malfunctions during operation – Charge air
pressure too high ......................................................... 62
Table25: Malfunctions during operation – Engine
performance losses ..................................................... 62
Table26: Malfunction – Turbocharger pumping.... 63
Table27: Malfunction – Sporadic surge blows ........ 63
Table28: Malfunctions when stopping – Runout
noises............................................................................... 64
Table29: Malfunctions when stopping – Runout
time too short ................................................................ 64
Table30: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 65
Table31: Malfunction of the speed measurement
system – Measured speed too high ........................... 65
Table32: Malfunction of the speed measurement
system – Measured speed too low............................. 65
Table33: Swivel lifting eyes......................................... 68
Table34: Ring nuts to be used.................................... 69
Table35: Weights of assemblies ................................ 70
Table36: 3 press-off screws........................................ 75
Table37: 6 press-off screws........................................ 76
Table38: Permissible clearances A and B ................. 84
Table39: Permitted nozzle ring compression PD ... 85
Table40: Tightening torque (51007) ......................... 88
Table41: Tightening torque (79041).......................... 90
Table42: Tightening torque (72011) .......................... 91
Table43: Permissible clearances N and R................. 92
Table44: Tightening torque (72020)......................... 93
Table45: Tightening torque (51009)......................... 96
Table46: Tightening torques...................................... 98
Table47: Tightening torques for insulation............. 99
Table48: Cover plate dimensions [mm] ................. 103
Table49: Customer spare part set 97070 .............. 107
Table50: Spare parts list ........................................... 109
Page 111 / 111Page 111 / 111