ABB ACQ80-04 - Page 194

194 Additional parameter data
82.47 Dry run trip monitor time Real 1.0...300.0 s 10 = 1
82.48 Dry run reset time Real 1.0...18000.0 s 10 = 1
83 Pump cleaning
83.01 Pump cleaning status List 1...4 - 1 = 1
83.02 Pump cleaning progress Real 0...100 % 1 = 1
83.03 Total cleaning count Real 0...1000000 - 1 = 1
83.12 Start pump cleaning Binary src 0...4 - 1 = 1
83.16 Cycles in cleaning program Real 1...65535 - 1 = 1
83.20 Cleaning speed step Real 0...3000 rpm 1 = 1
83.25 Time to cleaning speed Real 0.000...60.000 s 1 = 1
83.26 Time to zero-speed Real 0.000...60.000 s 1 = 1
83.27 Cleaning on time Real 0.000...1000.000 s 1 = 1
83.28 Cleaning off time Real 0.000...1000.000 s 1 = 1
95 HW configuration
95.01 Supply voltage List 0, 2 - 1 = 1
95.02 Adaptive voltage limits List 0…1 - 1 = 1
95.03 Estimated AC supply voltage Real 0…65535 V 1 = 1 V
95.04 Control board supply List 0…1 - 1 = 1
95.15 Special HW settings PB 0b0000…0b1111 - 1 = 1
95.20 HW options word 1 PB 0b0000…0b1111 - 1 = 1
95.200 Cooling fan mode List 0, 1 - 1 = 1
96 System
96.01 Language List 0, 1033, 2052 - 1 = 1
96.02 Pass code Data --1 = 1
96.03 Access level status PB 0b0000...0b1111 - 1 = 1
96.04 Macro select List 0, 1, 13...27 - 1 = 1
96.05 Macro active List 0, 1, 13...27 - 1 = 1
96.06 Parameter restore List --1 = 1
96.07 Parameter save manually List 0, 1 - 1 = 1
96.08 Control board boot List 0, 1 - 1 = 1
96.10 User set status List 0...11 - 1 = 1
96.11 User set save/load List 0...5, 18...21 - 1 = 1
96.12 User set I/O mode in1 Binary src --1=1
96.13 User set I/O mode in2 Binary src --1=1
96.16 Unit selection PB 0b0000...0b1111 - 1 = 1
96.20 Time sync primary source List - -1 = 1
96.51 Clear fault and event logger Real 0…1 - 1 = 1
(Parameters 96.100…96.102 only visible when enabled by parameter 96.02)
96.100 Change user pass code Data 10000000…99999999 - 1 = 1
96.101 Confirm user pass code Data 10000000…99999999 - 1 = 1
96.102 User lock functionality PB 0000h…FFFFh - 1 = 1
97 Motor control
97.01 Switching frequency reference List - kHz 1 = 1 kHz
97.02 Minimum switching frequency List - kHz 1 = 1 kHz
97.13 IR compensation Real 0.00…50.00 % 100 = 1%
97.20 U/F ratio List 0…20 - 1 = 1
97.49 Slip gain for scalar Real 0...200 % 1 = 1%
97.94 IR comp max frequency Real 1.0...200.0 % 10 = 1%
98 User motor parameters
98.01 User motor model mode List 0…1 - 1 = 1
98.02 Rs user Real 0.0000…0.50000 p.u. 100000 =
1 p.u.
98.03 Rr user Real 0.0000…0.50000 p.u. 100000 =
1 p.u.
98.04 Lm user Real 0.00000…10.00000 p.u. 100000 =
1 p.u.
98.05 SigmaL user Real 0.00000…1.00000 p.u. 100000 =
1 p.u.
No. Name Type Range Unit FbEq32
ACQ80 FW.book Page 194 Thursday, February 14, 2019 11:33 AM