ADCMT 6243 User Manual

6243/44 DC Voltage Current Source/Monitor Operation Manual
3.4.2 6244 Setting Ranges and Factory Settings
3-22
3.4.2 6244 Setting Ranges and Factory Settings
Panel key Parameter group Parameter type Range Factory setting
SOURCE
Source mode
Source function
Source range
Source value
Limit
DC/PLS/SWP/PSW
VS/IS
320 mV to 20 V/320 A to 10 A
0.00 mV to 20 V/0.00 A to  10 A
3 mV to 20 V/3 A to 10 A
DC
VS
320 mV
+000.00 mV
04.000 A
MEASURE
Measurement function
Measurement auto range
Null calculation
DC & pulse trigger mode
VM/IM
Auto / Fixed range
ON/OFF
RUN/HOLD
IM
Fixed (10A range)
OFF
RUN
MENU
SWEEP
Sweep type
Bias value
Start value
Stop value
Step value
Number of Logs and steps
Start address
Stop address
Sweep ranging
Number of sweep repeats
Reverse mode
Sweep trigger mode
Linear/Log/Random
0.00 mV to 20 V/0.00 A to 10 A
0.00 mV to 20 V/0.00 A to 10 A
0.00 mV to 20 V/0.00 A to 10 A
0.01 mV to 20 V/0.01 A to 10 A
1/2/5/10/25/50 (Step/Decade)
0 to 4999
0 to 4999
Auto/Fixed
0 to 1000
ON/OFF
Internal/External
Linear
+000.00 mV
+000.01 mV
+001.00 mV
000.01 mV
10 Step/Decade
0
0
Auto Range
1
OFF
Internal
TIME
Measure delay time
Source delay time
Hold time
Period
Pulse width
Auto-range display time
0.30 ms to 60000 ms
0.01 ms to 60000 ms
3 ms to 60000 ms
2.00 ms to 60000 ms
1.00 ms to 60000 ms
0 ms to 500 ms
4.00 ms
0.01 ms
00010 ms
50.00 ms
25.00 ms
00000 ms
SOURCE
Pulse base value
Li
miter polarity mode
Remote sensing
Limiter / OSC Buzzer
0.00 mV to 20 V/0.00 A to 10 A
Auto/Plus/Minus
2 Wire/4 Wire
ON/OFF
000.00 mV
Auto
2 Wire
OFF
MEASURE
integration time
Auto zero
Number of digits for measurement
Measurement ON/OFF
Display ON/OFF
500 s/1 ms/10 ms/1 PLC/10 PLC/100 PLC
ON/OFF
5 1/2 or 4 1/2
ON/OFF
ON/OFF
1 PLC
ON
5 1/2
ON
ON
COMPARATOR
Comparator calculation
Comparator -upper limit
Comparator -lower limit
Comparator result buzzer
ON/OFF
0.000 mV to 20 V/0.000 A to 10 A
0.000 mV to 20 V/0.000 A to 10 A
ON/OFF
OFF
+000.000 A
+000.000 A
OFF
EXT.SIGNAL
External control signal
Complete output mode
External Control signal - pulse
width
OPR In (On/Off)/Interlock/OPR Out
Complete Out (Front/End/HI/GO/LO) /
Busy (In/Out)
20 s/100 s
Operate Off In
Complete Out End
20 s

ADCMT 6243 Specifications

General

Brand	ADCMT
Model	6243
Category	Measuring Instruments
Language	English