8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier C Additional Rinse
Time CNP 7
This option allows the owner to add additional time to agitate
steps that have Rinse 1 selected as their status. The additional
rinse time option needs to be turned on for the Cycle Modifier C
Additional Rinse Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
CNP- appears in the display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until CNP
7 appears in the display.
6.
When CNP 7 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Rinse 1
selected as their status.
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to increase or decrease the current number of minutes
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Enter Cycle Programming Cy-
CLE-
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until Cy-
CLE- appears in the display. Press the START (enter) keypad
and CyCLE1 will appear in the display.
NOTE: The LED light next to the select cycle keypad
will be lit to indicate which cycle is being program-
med.
4. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the cycles to program.
5. Press the START (enter) keypad when the desired cycle ap-
pears in the display. PCyCtd will appear in the diplay if ena-
bled. Otherwise the first cycle step will appear. Refer to Table
11 for keypad navigation.
6. For each cycle, the Programmable Cycle Time Display can be
programmed, if enabled in Global Programming Parameters
(refer to Programmable Cycle Time Display PCyCtd). Press
the START (enter) keypad to program the displayed time.
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until the desired value is on the diplay. Values range
from 0 - 65,535. A value of 0 will disable Programmable Cy-
cle Time for the selected cycle. This allows for some cycles to
use a Programmable Cycle Time while others use the time
calculated from the enabled steps.
8. Press the START (enter) keypad. The new value is saved and
01XXXX appears in the dispay. The first two digits represent
the Cycle Step number and will flash. XXXX will show the
step type. The machine is able to have up to 50 custom steps
programmed for each cycle. Within each step there are several
programmable options. Refer to the following sections for de-
tails about each step type and its options.
9.
After the last cycle step is stored, CyCEnd is diplayed. If 50
steps are programmed CycEnd will not be displayed. To in-
sert a step at the end of the cycle, first go to this display and
then press the NORMAL 90key pad.
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
73 Part No. 805405ENR5
To Next Page
Loading...
