3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
CNP- appears in the display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until CNP
3 appears in the display.
6.
When CNP 3 appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the DELI-
CATES 30 (<) keypad.
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the configuration value.
Refer to Table 10 for the value definitions.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier B Additional Wash
Time CNP 4
This option allows the owner to add additional time to agitate
steps that have wash selected as their status. The additional wash
time option needs to be turned on for the Cycle Modifier B Addi-
tional Wash Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
CNP- appears in the display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until CNP
4 appears in the display.
6.
When CNP 4 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to agitate steps that have
wash selected as their status.
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to increase or decrease the current number minutes.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier B Additional Rinse
Time CNP 5
This option allows the owner to add additional time to agitate
steps that have Rinse 1 selected as their status. The additional
rinse time option needs to be turned on for the Cycle Modifier B
Additional Rinse Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
CNP- appears in the display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5.
When CNP 5 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Rinse 1
selected as their status.
6. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to increase or decrease the current number of minutes.
NOTE: To go back to the current programmable op-
tion without changing the value, press the DELI-
CATES 30 (<) keypad.
7. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier C Additional Wash
Time CNP 6
This option allows the owner to add additional time to agitate
steps that have wash selected as their status. The additional wash
time option needs to be turned on for the Cycle Modifier C Addi-
tional Wash Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
CNP- appears in the display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until CNP
6 appears in the display.
6.
When CNP 6 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Wash se-
lected as their status.
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to increase or decrease the current number of minutes.
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
72 Part No. 805405ENR5
To Next Page
Loading...
