ALLIANCE BF3JGBJG403UN01 - Special Vend 4 Days Enable SP4

This option allows the owner to enable or disable third special
vend. Special Vend 3 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 3 op-
tion on or off.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until SP3
appears in the display.
4.
When SP3 appears in the display, press the START (enter)
keypad. The current Special Vend 3 Days Enable status will
appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 4 Days Enable SP4
This option allows the owner to enable or disable a fourth special
vend. Special Vend 4 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 4 op-
tion on or off if desired.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until SP4
appears in the display.
4.
When SP4 appears in the display, press the START (enter)
keypad. The current Special Vend 4 Days Enable status will
appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Modifier Programming CNP-
This option allows the owner to program the machine to offer an
added prewash, extra wash time, an added rinse, extra rinse time,
a warm rinse, or any combination of the above to the customers
for an added vend price. This option is used when B or C is selec-
ted using the modifier keypad.
How to Program Default Cycle Modifier CNP 1
This option allows the owner to set the Default Cycle Modifier.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the NORMAL 40 (∨) keypad to
scroll through the programmable options until CNP- appears
in the display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable Cycle Modifier
options until CNP 1 appears in the display.
6.
When CNP 1 appears in the display, press the START (enter)
keypad. A number will appear in the display. This number
corresponds to the current default cycle modifier. Refer to ta-
ble below.
CNP 1
Default Value Cycle Modifier
0* A
1 B
2 C
*Factory default setting.
Table 9
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to increase or decrease the current number to the de-
sired number selected from the table.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier B Key #1 Options
CNP 2
This option allows the owner to select the options that are ena-
bled when the B modifier keypad is active.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
69 Part No. 805405ENR5