5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
OPL Parameters oPL-
This option allows the owner to enable or disable the OPL Pa-
rameters in which no vend price needs to be satisfied to operate
the machine.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
oPL- appears in the display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the OPL submenu options.
6. Press the START (enter) keypad when the desired option ap-
pears in the display
OPL Mode Enable oPL 1
This option allows the owner to place the control in OPL Mode,
in which no vend price needs to be satisfied in order to start the
machine. If the control is in Start Mode, the cycle time will be
displayed. Pressing the START keypad will start the machine cy-
cle. Once a machine cycle has been started, each additional press
of the START keypad will advance the cycle to the next cycle
step only if Rapid Advance Programming Parameter is Enabled.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
oPL- appears in the display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until oPL
1 appears in the display.
6.
When oPL 1 appears in the display, press the START (enter)
keypad. The current OPL status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
OPL Delayed Start oPL 2
This option allows the owner to enable delayed start mode which
can delay the cycle up to a maximum of 72 hours.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
oPL- appears in the display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until oPL
2 appears in the display.
6.
When oPL 2 appears in the display, press the START (enter)
keypad. The current OPL status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
7. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
OPL Display Power Save oPL 3
This option allows the owner to enable the OPL Display Power
Save Feature. If enabled, after 255 seconds of no user input, the
control will turn off all LEDs and the display until user input oc-
curs. The OPL Display Power Save Feature will only turn off the
display if the control is in Start Mode.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
oPL- appears in the display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until oPL
3 appears in the display.
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
93 Part No. 805405ENR5
To Next Page
Loading...
