4.
When SUnitS appears in the display, press the START (en-
ter) keypad. The current Speed Units status will appear in the
display.
rPN = Option (factory default setting)
gForCE = Option
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programmable Close Door Display
PCdL
This option allows the owner to enable or disable allowing the
control to display the corresponding command to close the door
along with the cycle time.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
PCdL appears in the display.
4.
When PCdL appears in the display, press the START (enter)
keypad. The current status will appear in the display.
on = Option Enabled (factory default setting)
oFF = Option Disabled
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programmable Push Start Display PPSt
This option allows the owner to enable or disable allowing the
control to display the corresponding command to press the
START (enter) keypad once the vend has been satisfied.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
PPSt appears in the display.
4.
When PPSt appears in the display, press the START (enter)
keypad. The current Push Start status will appear in the dis-
play.
on = Option Enabled (factory default setting)
oFF = Option Disabled
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programmable Open Door Display PodL
This option allows the owner to enable or disable allowing the
control to display the corresponding command to open the door
along with the cycle time when the cycle had completed.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
PodL appears in the display.
4.
When PodL appears in the display, press the START (enter)
keypad. The current status will appear in the display.
on = Option Enabled (factory default setting)
oFF = Option Disabled
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price Display Override AtS do
This option allows the owner to override the previously set vend
price with a custom display that is set by the payment system.
The default display is CArd if the payment system does not mod-
ify it.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
“ AtS do ” appears in the display.
4.
When AtS do appears in the display, press the START (en-
ter) keypad. The current Vend Price Display Override status
will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
92 Part No. 805405ENR5
To Next Page
Loading...
