Copyright © 1996 General Motors Corp. 4–5
GENERAL OVERHAUL INFORMATION
Table 4–1. Special Tools
Tool No. Figure Item Description Ref. Paragraph
J 3289-20 4–2 23 Transmission holding fixture base (used with
J 23642-01)
5–3
a
J 3453 4–4 75 Universal yoke and flange holder NR
J 5959-1 4–4 50 Dial indicator (used with J 5959-3, J 5959-7,
J 7872-2, J 7872-3, and J 24602)
6–3
b
J 5959-3 4–4 52 Rod
1
⁄
4
x 10
1
⁄
2
inches (used with J 5959-1, J 5959-7,
J 7872-2, J 7872-3, and J 24602)
6–3
b
J 5959-7 4–4 54 Lug attachment (used with J 5959-1, J 5959-3,
J 5959-7, J 7872-2, J 7872-3, and J 24602)
6–3
b
J 6125-1B 4–2 29, 30 Front support slide hammer (2) 5–3
i
J 6125-2 4–2 31 Slide hammer adapter (2) 5–3
i
J 7872-2 4–4 55 Magnetic clamp (used with J 5959-1, J 5959-3,
J 5959-7, J 7872-3, J 24602)
6–3
b
J 7872-3 4–4 56 Swivel adapter (used with J 5959-1, J 5959-3,
J 5959-7, J 7872-2)
6–3
b
J 8092 4–2 5 Universal driver handle (used with J 23615, J 24451,
J 24778, J 25356)
6–9
d
, 6–14
b
J 21279-01 4–4 67 Engine stand adapter plate
J 21359-A 4–2 2 Oil pump seal installer 6–9
d
J 21362 4–4 46 Forward and fourth clutch inner seal protector 6–10
b
, 6–12
b
J 21369-E 4–2 22 Converter leak test fixture 6–3
c
J 21409 4–4 48 Seal protector (tangless piston) forward and fourth
clutch (same as J 23779-01 without tang slots)
NR
J 21795-4 4–2 12 Thumb screw for J 24352 7–6
a
J 23549 4–4 65 Stator thrust bearing installer (used with J 24202-4) 6–4
c
J 23614-A 4–2 6 Stator shaft front bushing installer (also front and rear
sun gear shaft bushings) (models without lockup)
6–9
b
, 6–14
b
J 23615 4–2 3 Stator shaft rear bearing installer (used with J 8092) 6–9
d
J 23616 4–2 9 Forward and fourth clutch spring compressor 6–10
a
,
c
, 6–12
a
,
c
J 23619-01 4–2 19 Forward clutch clearance gauge (for housings without
ID groove)
6–10
b
, 6–12
b
J 23630-02 4–2 25 First clutch spring compressor assembly (includes
J 23630-1, J 23630-2, J 23630-3)
5–3
q
, 7–4
a
, 7–6
a
J 23630-1 4–2 27 First clutch spring compressor 5–3
q
, 7–4
a
,
f
,
k
J 23630-2 4–2 26 First clutch spring compressor base (used
separately to position components during end play
measurement and thrust washer selection)
7–4
a
, 7–6
a
, 7–8
b
J 23630-3 4–2 28 Press bolt and nut 5–3
q
, 7–4
a
To Next Page
Loading...
Need help?
General
