4–6 Copyright © 1996 General Motors Corp.
AT 500, 1500 SERIES AUTOMATIC TRANSMISSIONS
J 23631 4–2 1 Output shaft seal installer 3–16
g
, 7–9
a
J 23632-01 4–2 15 Spacer selection gauge 7–6
a
J 23633 4–2 13 Thrust washer selection gauge bar 7–8
a
J 23642-01 4–2 24 Transmission holding fixture and shaft
(used with J 3289-20)
5–3
a
, 7–12
a
J 23643 4–2 10 Center support lifting bracket 5–3
n
, 7–5
b
J 23715 4–2 20 First clutch clearance gauge 7–4
b
J 23716 4–2 21 Third clutch clearance gauge 7–7
a
, 7–12
b
J 23717-C 4–2 33 Center support compressor assembly (used with
J 34127)
7–5
b
J 23717-4 4–2 34 Snapring gauge (replaced by gauge J 34127)
J 23718-02 4–4 68 Output shaft positioning sleeve NR
J 23779-01 4–4 48 Forward and fourth clutch outer seal protector NR
J 24202-4 4–4 51 Driver handle (used with J 23549) 6–4
c
J 24216-01 4–4 47 First clutch inner seal protector 7–4
a
J 24218-1 4–4 60 Stator roller retainer ring (2
13
⁄
16
inch OD) 6–4
d
J 24314 4–2 7 Shift valve adjusting ring tool 3–13
b
, 6–6
b
J 24352 4–2 11 Sun gear shaft retainer assembly 7–6
a
,
b
J 24420-B 4–4 59 Rear bearing puller body (used with J 24463-2 or
J 38086-A)
3–16
c
J 24446 4–4 61 Rear bearing installer (with or without output shaft
installed)
3–16
f
, 7–6
a
J 24451 4–2 4 Output shaft bushing installer (used with J 8092) 6–14
b
J 24453 4–4 49 Retainer ring installer 6–13
c
J 24463 4–4 57 Rear bearing puller assembly (in vehicle) (includes
J 24420-B and J 24463-2 or J 38086-1)
3–16
c
J 24463-2 4–4 58 Rear bearing puller legs (2) (used with J 24420-B)
(use if bearing is a 10-ball bearing)
3–16
c
J 24602 4–2 14 Converter end play gauge (used with J 5959-1,
J 5959-3, J 5959-7, J 7872-2, and J 7872-3)
6–3
b
J 24773-A 4–3 43 Pump support assembly remover 5–3
i
J 24778 4–4 62 Center support bushing installer (models without
lockup)
6–13
c
J 24787 4–4 63 Main-pressure regulator valve installer or remover 6–9
a
,
d
J 25000-1 4–3 42 Valve body and governor test stand (used with
J 25000-225)
3–13
a
J 25000-225 4–3 40 Valve body test stand adapter (used with J 25000-1) 3–13
a
Table 4–1. Special Tools
(cont’d)
Tool No. Figure Item Description Ref. Paragraph
To Next Page
Loading...
Need help?
General
