APT 300XAC Series User Manual

iii
4.4.2 Naming a Memory ......................................................................... 59
4.4.3 Selecting a Step ............................................................................ 60
4.5 Test Parameters Description ................................................................. 60
4.6 Editing Test Parameters ........................................................................ 65
4.6.1 Editing Start and End Angle (PROGRAM Mode only) ................... 66
4.6.2 Editing the Memory Cycle (PROGRAM Mode only) ...................... 68
4.6.3 Editing the Memory (PROGRAM Mode only) ................................ 69
4.6.4 Editing the Step (PROGRAM Mode only) ...................................... 69
4.6.5 Editing Voltage .............................................................................. 70
4.6.6 Editing Frequency.......................................................................... 71
4.6.7 Editing Transient * (PROGRAM Mode only) .................................. 71
4.6.8 Editing Trans-Volt* (PROGRAM Mode only) .................................. 72
4.6.9 Editing Trans-Site* (PROGRAM Mode only) ................................. 73
4.6.10 Editing Trans-Time* (PROGRAM Mode only) ................................ 74
4.6.11 Editing Trans-Cycle* (PROGRAM Mode only) ............................... 74
4.6.12 Editing Ramp Up (PROGRAM Mode only) .................................... 76
4.6.13 Editing Timer Unit (PROGRAM Mode only) ................................... 77
4.6.14 Editing Delay (PROGRAM Mode only) .......................................... 77
4.6.15 Editing Dwell (PROGRAM Mode only) .......................................... 78
4.6.16 Editing Ramp Down (PROGRAM Mode only) ............................... 79
4.6.17 Editing Step Cycle (PROGRAM Mode only) .................................. 79
4.6.18 Editing A Hi-Lmt & A Lo-Lmt (PROGRAM Mode only) ................... 80
4.6.19 Editing P Hi-Lmt & P Lo-Lmt (PROGRAM Mode only) .................. 81
4.6.20 Editing Ap Hi-Lmt & Ap Lo-Lmt (PROGRAM Mode only) ............... 82
4.6.21 Editing CF Hi-Lmt & CF Lo-Lmt (PROGRAM Mode only) .............. 83
4.6.22 Editing PF Hi-Lmt & PF Lo-Lmt (PROGRAM Mode only) .............. 84
4.6.23 Editing VA Hi-Lmt & VA Lo-Lmt (PROGRAM Mode only) .............. 85
4.6.24 Editing Q Hi-Lmt & Q Lo-Lmt (PROGRAM Mode only) .................. 87
4.6.25 Editing Prompt ............................................................................... 88
4.6.26 Editing Connect ............................................................................. 89
4.6.27 Editing Phase Set (Option 08 – PROGRAM Mode only) ............... 89
4.7 Reviewing Test Results ......................................................................... 90
5. Test Modes .................................................................................................. 92
5.1 Description of Test Modes .................................................................... 92
5.2 Initializing a Test in PROGRAM Mode .................................................. 92
5.2.1 AC Output ...................................................................................... 92
5.2.2 DC Output ..................................................................................... 94
5.3 Initializing a Test in MANUAL Mode ...................................................... 96
5.3.1 AC Output ...................................................................................... 96
5.3.2 DC Output ..................................................................................... 97
6. Multiple Instrument Operation ...................................................................... 99
6.1 Configuring Sources for Parallel and Polyphase Operation .................. 99
6.1.1 Operating Mode Definitions ........................................................... 99
6.1.2 Connecting the Interface Cable ..................................................... 99
6.1.3 Output Wiring Diagrams .............................................................. 100
6.2 Power Up Considerations in Parallel and Polyphase Mode ................ 103

APT 300XAC Series Specifications

General

Brand	APT
Model	300XAC Series
Category	AC Power Distribution
Language	English