BluStream IP100UHD-TX - RS-232 and Telnet Commands

MULTICAST USER MANUAL
56
www.blustream.co.uk
COMMAND DESCRIPTION COMMAND RESPONSE
Set Input: yyy EDID To Default EDID:zz (yyy:001~762)
zz=00: HDMI 1080p@60Hz, Audio 2CH PCM
zz=01: HDMI 1080p@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=02: HDMI 1080p@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=03: HDMI 1080i@60Hz, Audio 2CH PCM
zz=04: HDMI 1080i@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=05: HDMI 1080i@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=06: HDMI 1080p@60Hz/3D, Audio 2CH PCM
zz=07: HDMI 1080p@60Hz/3D, Audio 5.1CH PCM/DTS/DOLBY
zz=08: HDMI 1080p@60Hz/3D, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=09: HDMI 4K2K 4:4:4, Audio 2CH PCM
zz=10: HDMI 4K2K 4:4:4, Audio 5.1CH PCM/DTS/DOLBY
zz=11: HDMI 4K2K 4:4:4, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=12: DVI 1280x1024@60Hz, Audio None
zz=13: DVI 1920x1080@60Hz, Audio None
zz=14: DVI 1920x1200@60Hz, Audio None
zz=15: Default EDID
zz=16: 4K2K 4:2:0 @ 60Hz, Audio 2CH PCM
zz=17: 4K2K 4:2:0 @ 60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=18: 4K2K 4:2:0 @ 60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
INyyyEDIDzz Set INPUT:yyy to Setting EDID: zz
Set Video Wall OUTPUT:xxx (xxx:001~762)
Rows Max number:aa (aa:01~30)
Columns Max number:bb (bb:01~30)
Rows Position index (mm:01~30)
Columns Position index (nn:01~30)
OUTxxxVWaaXbbRmmCnn Set OUTPUT:xxx To aaXbb Rows
index:mm Columns index:nn
OUTPUT:xxx Restore factory settings (xxx:001~762) OUTxxxRESET Set OUTPUT:xxx RESET
INPUT:xxx Restore factory settings (xxx:001~762) INxxxRESET Set INPUT:yyy RESET
OUTPUT:xxx Reboot (xxx:001~762) OUTxxxREBOOT Set OUTPUT:xxx REBOOT
INPUT:xxx Reboot (xxx:001~762) INxxxREBOOT Set INPUT:xxx REBOOT
OUTPUT:xxx HDR ON (xxx:001~762) OUTxxxHDRON Set OUTPUT:xxx HDR ON
OUTPUT:xxx HDR OFF (xxx:001~762) OUTxxxHDROFF Set OUTPUT:xxx HDR OFF
OUTPUT:xxx STATUS (xxx:001~762) OUTxxxSTATUS Multicast IP:
xx.xx.xx.xx
Channel:
xxxx
Ethernet Link Status:
on/o
Video Status:
WAITING_HOST_MODE
Please Enter command:
INPUT:yyy STATUS (yyy:001~762) INxxxSTATUS Multicast IP:
xx.xx.xx.xx
Channel:
xxxx
Ethernet Link Status:
on/o
Video Status:
WAITING_HOST_MODE
Please Enter command:
When command is successful Success!
Please Enter command:
When command fails (time out) Fail!
Please Enter command:
When command has error error command!
Please Enter command:
RS-232 and Telnet Commands