3
Bosch Security Systems 10/22 BLCC615R
Solution 6000-IP
Quick Start Guide
FIGURES
Figure 1: PCB and Mounting Clip Installation Diagram ...................5
Figure 2: Tamper Bracket Installation ..................................................... 5
Figure 3: MW720B - Small Enclosure Details .......................................6
Figure 4: PCB Mounting Clip .....................................................................6
Figure 5: MW720B Configuration Examples ........................................6
Figure 6: MW730B - Large Enclosure Details .......................................7
Figure 7: MW730B Configuration Examples ........................................7
Figure 8: Internal Transformer Connection Diagram ........................8
Figure 9: N/C No EOL Zone ........................................................................9
Figure 10: N/C Single EOL Zone ...............................................................9
Figure 11: N/C Split EOL Zone ...................................................................9
Figure 12: N/C Zone With Tamper............................................................9
Figure 13: N/O No EOL Zone .....................................................................9
Figure 14: N/O Single EOL Zone ...............................................................9
Figure 15: N/O Split EOL Zone ..................................................................9
Figure 16: N/O Zone With Tamper ...........................................................9
Figure 17: EOL Resistor Colour Chart .....................................................9
Figure 18: LAN Connection Using 2 Pair Security Cable ............... 10
Figure 19: LAN Connection Using Twisted Pair Cable ................... 11
Figure 20: Solution 6000-IP Board Layout ......................................... 12
Figure 21: Solution 6000-IP Connection Diagram .......................... 13
Figure 22: Keypad Emergency Alarm Trigger’s ................................ 15
Figure 23: Keypad DIP Switch Address Settings .............................. 17
Figure 24: Rotary Swich Address Settings ......................................... 17
Figure 25: Sample Option Bit Menu Display ..................................... 18
Figure 26: Area Text Programming Display ......................................18
Figure 27: List Option Programming Display ................................... 19
Figure 28: Clock Programming Display .............................................. 19
Figure 29: Custom Installer Baner Sample......................................... 47
TABLE OF CONTENTS
Copyright Notice ....................................................................................2
Trademarks ...............................................................................................2
Notice of Liability ....................................................................................2
FEATURES ���������������������������������������������������������������������������������4
OVERVIEW ��������������������������������������������������������������������������������4
ABOUT THE PANEL ������������������������������������������������������������������� 5
Enclosures .................................................................................................5
Enclosure Fixing Method .....................................................................5
Installing The Tamper Switch .............................................................5
Enclosure Module Spaces .................................................................... 5
Installing Panels and Modules ...........................................................6
Connecting Power To The Panel ........................................................8
Connecting The Battery .......................................................................8
AC Mains Transformer Option ............................................................ 8
Panel LED Indicators .............................................................................. 8
WIRING DIAGRAMS������������������������������������������������������������������9
EOL Resistor Colours and Values .......................................................9
LAN Overview ....................................................................................... 10
LAN Wiring ............................................................................................. 10
System Earthing ................................................................................... 11
Terminating the LAN .......................................................................... 11
PCB Layout ............................................................................................. 12
Connection Diagram .......................................................................... 13
Terminal Descriptions ........................................................................ 14
Board Connectors ................................................................................ 14
ABOUT THE KEYPAD ��������������������������������������������������������������15
Status Icons / LED’s ............................................................................. 16
Keypad Tones ........................................................................................ 16
Keypad & Readers Setup ................................................................... 17
DIP Switch Address Select ................................................................ 17
Rotary Switch Address Select .......................................................... 17
Programming Overview .................................................................... 17
Entering Programming Mode ......................................................... 17
Exiting Programming Mode ............................................................ 18
Navigating The Menu ......................................................................... 18
Command Menu .................................................................................. 18
Programming Option Bit Menus .................................................... 18
Alpha Text ............................................................................................... 18
List Options ............................................................................................ 19
Clock Programming ............................................................................ 19
GETTING STARTED WITH MYALARM �����������������������������������19
SERVICE MODE �����������������������������������������������������������������������19
DEFAULTING THE SYSTEM�����������������������������������������������������20
DIRECT LINK PROGRAMMING ����������������������������������������������20
ZONE ARRAY ��������������������������������������������������������������������������� 20
DOOR ARRAY ��������������������������������������������������������������������������20
OUTPUT ARRAY ���������������������������������������������������������������������� 21
BASIC REPORTING REFERENCE ��������������������������������������������21
MENU REFERENCE TABLE ������������������������������������������������������ 22
PROGRAM LOCATIONS ���������������������������������������������������������� 25
Access Programming ......................................................................... 25
User Default Table ............................................................................... 25
Area Programming .............................................................................. 27
Input Programming ............................................................................ 29
Zone Assignments .............................................................................. 30
Zone Default Table .............................................................................. 31
Output Programming ........................................................................ 33
Output Default Table .......................................................................... 33
Output Event Types ............................................................................ 34
Output Assignments .......................................................................... 35
One Shot Mode .................................................................................... 35
Pulsing Mode ........................................................................................ 35
Comms Programming ...................................................................... 37
Device Programming ......................................................................... 41
System Programming ........................................................................ 44
Testing The System ............................................................................. 48
Installation Details............................................................................... 49
Specifications ........................................................................................ 50
TABLES
Table 1: Expansion Options .......................................................................5
Table 2: Report Indicator LED ....................................................................8
Table 3: Status Indicator LED ..................................................................... 8
Table 4: Terminal Block Descriptions ................................................... 14
Table 5: Board Connector Descriptions .............................................. 14
Table 6: Keypad Key Functions .............................................................. 15
Table 7: ICON & LED Indicator Meanings ........................................... 16
Table 8: Keypad Tones ............................................................................... 16
Table 9: DIP Switch Address Settings .................................................. 17
Table 10: Rotary Switch Address Settings.......................................... 17
Table 11: Keys Used During Programming ........................................ 18
Table 12: Text Keypad Character Set ................................................... 18
Table 13: Shortform Point ID List .......................................................... 21
Table 14: Menu Structure And Layout ................................................ 24
Table 15: User Default Programming Options ................................. 25
Table 16: Zone Assignments ................................................................... 30
Table 17: Zone Defaults ............................................................................ 31
Table 18: Output Default Table .............................................................. 33
Table 19: Output Event Types ................................................................ 34
Table 20: Address Configuration and Output Assignments ....... 35
Table 21: One-Shot Polarity Example ................................................. 35
Table 22: Macros Script Characters ...................................................... 36
Table 23: Macros Operator Characters ................................................ 37
Table 24: Macros Scene Characters ...................................................... 37
Table 25: Macro Scene Operator Characters..................................... 37
To Next Page
Loading...
Need help?
General
