Cardinal 190 - Page 135

136 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

8400-M022-O1 Rev K  Model 190 Indicator

125

Table of Contents

Precautions3
- Table of Contents5
Specifications9
- Standard Features10
- Optional Features10
- European Declaration of Conformity11
Precautions12
- Static Electricity12
- Batteries12
Installation13
- Site Preparation Requirements13
- Environmental13
- Electrical Power14
- Electrical Noise Interference14
- Transient Suppression14
- Mounting15
- Load Cell Connections16
- Load Cell Connections with over 30 Feet of Cable17
- Sense and Dead Load Jumpers17
- Serial and I/O Cable Installation18
- P3 I/O Connections (Refer to Figure No. 6)18
- P2 Power Connections (Refer to Figure No. 6)18
- P3 I/O Interconnection Diagram19
- Re-Installing the Front Panel19
Indicator Setup20
- Calibration Inhibit Jumper20
- Calibration Data Entry21
- Accessing Setup22
- Settings23
- Analog to Digital Filtering29
- Filter Setting Recommendations31
- Calibration32
- Dual-Point with Zero (First Zero) Calibration33
- Dual-Point Without Zero (False Zero) Calibration34
- Single-Point for Span Only (Last Zero) Calibration35
- Single-Point for Zero Only (Only Zero) Calibration36
- Multi-Point Calibration37
- Calibration "C" Numbers39
- Set Gravity Constant40
- Serial Input/Output41
- Print Tab Settings44
- Fine Span Adjustment47
- Display High Resolution Weight48
- Key Lockout Feature49
- Options Setup51
- Function Setup53
- Display Backlight Color Setup55
Keypad57
- Standard Key Functions57
- Fn/ Key Functions60
- Fn/ Key Combination Features61
Annunicators62
- Battery Status64
Indicator Setup Review65
- Accessing Setup Review65
Operation67
- Ticket Format Selection67
- Preset Weight Comparators68
- Hold Function69
- Count Function70
- Time and Date Functions71
- Peak Hold Function72
- Checkweigher73
- Live Weight Function75
- Accumulated Weight Function76
- Touch Key Lock out Function77
- ASCII Commands78
Error Messages83
- Before You Call Service83
- Error Codes84
Event Counters85
- Accessing the Event Counters85
Test Mode/ Diagnostics87
- Accessing Test Mode/Diagnostics87
Parts Identification88
- Front Sub-Assembly88
- Rear Sub-Assembly90
- AC Wiring (Detail C)91
- Power Supply Sub-Assembly92
- P2 Wiring Detail93
- P2 Wiring Detail with 190-DAC Option Card93
- 190DC and 190LS Rear Sub-Assembly94
- 190DC Power Supply Sub-Assembly95
- 190DC Wiring Detail B96
- 190DC POWER OPTIONS (Not Shown)96
Appendix A - Bp190 Optional Battery Pack98
- BP190 Contents98
- BP190 Specifications98
- Installing the BP19099
APPENDIX B - Model 190A101
- Traffic Control101
- Axle Weighing Mode101
- Standard Axle Weighing Operation103
- Auto Axle Weighing Operation105
- Wiring106
- Scoreboard Interconnections107
APPENDIX C - 190-RS232 Option108
- Operation108
- Specifications108
- Onboard Status/Diagnostic Led's108
- Serial Option Card P4 Wiring108
- Setup109
APPENDIX D - 190-IP Option112
- Features112
- Onboard Status/Diagnostic Led's112
- Setup113
- Ethernet Cable Installation114
- IP Address Setup114
- 190-IP Operation114
- XPORT Connector Status Led's115
APPENDIX E - 190-Wifi Option116
- Specifications116
- Onboard Status/Diagnostic Led's117
- Setup118
- Network Configuration120
- Wi-Fi Operation124
APPENDIX F - 190-DAC Option125
- Specifications125
- Onboard Status/Diagnostic Led's126
- Setup127
- DAC Wiring129
APPENDIX G - 190-USB Option130
- Features130
- Onboard Status/Diagnostic Led's130
- Setup131
- 190-USB Operation132

Related product manuals

Preview: Cardinal 190 Series

Cardinal 190 Series

Preview: Cardinal 212 Series

Cardinal 212 Series