Carrier ChillerVu - Mounting the Carrier Chillervu

To Next Page

To Previous Page

Mounting the Carrier® ChillerVu™

Carrier® ChillerVu™

WARNING

When you handle the Carrier® ChillerVu™:

• Do not contaminate the printed circuit board with fingerprints, moisture, or any foreign material.

• Do not touch components or leads.

• Handle the board by its edges.

• Isolate from high voltage or electrostatic discharge.

• Ensure that you are properly grounded.

Screw the Carrier® ChillerVu™ into an enclosed panel using the mounting slots on the cover plate. Leave about 2

in. (5 cm) on each side of the controller for wiring. See mounting dimensions in Specifications.

If using expanders, see Installing an expander (page 12) before mounting the controller.

Mounting the Carrier® ChillerVu™

Main Page

Table of Contents3
What Is the Carrier® Chillervu5
- Carrier® Chillervu™ Specifications6
- Using Expanders8
- MPC Open XPIO48 and MPC Open XPIO816 Specifications9
- Safety Considerations10
Mounting the Carrier® Chillervu11
Wiring the Carrier® Chillervu™ for Power12
- To Wire for Power12
Addressing the Carrier® Chillervu13
- To Choose an IP Addressing Scheme13
- To Use a Default IP Address14
- To Obtain an IP Address Using DHCP15
- To Assign a Custom IP Address15
Installing an MPC Open XPIO Expander16
- To Mount an Expander16
- To Wire the Expander for Power18
- To Attach Expanders18
- To Set the Expander's Address19
Wiring Inputs and Outputs20
- Input Wiring Specifications20
- Inputs21
- Output Wiring Specifications21
- Outputs22
- To Wire Inputs and Outputs22
- To Use the Auto-Off-On Switches25
Wiring for Communications26
- Ethernet, Bacnet MS/TP, ARC156, and CCN Wiring Specifications27
- To Wire the Controller to the Bacnet MS/TP or ARC156 Network27
- To Connect the Carrier® Chillervu™ to the Ethernet28
- To Wire to the Bacnet over IP Network (DHCP)28
- To Wire to a Bacnet over IP Network (Assign a Custom IP)29
- To Wire to a CCN Network30
Wiring for Third Party Protocols31
- To Wire to Modbus RTU on Port S231
- To Wire to a Modbus over IP Network32
- To Connect to the Lonworks Network Using the Lonworks Option Card33
- To Connect to the Lonworks Network Using the SLTA-1033
- To Set the IP Address Using Putty34
Wiring Devices to the Carrier® Chillervu™'S Rnet Port36
Adding the Carrier® Chillervu™ into the I-Vu® or Field Assistant System37
- To Prepare to Create Your System37
- Find and Upload the Carrier® Chillervu™ as an Open Router38
- To Scan in and Download CCN Devices38
- To Add Control Programs and Graphics in the I-Vu® Interface40
- Configuring Third Party Protocols in the I-Vu® Interface41
Configuring CCN PIC Files to Communicate with Chiller Manager43
Configuring Bacnet Device Instance and Network Number44
- To Set up Bacnet Broadcast Management Devices (Bbmds)45
To Set up the Driver49
- Driver49
- Device50
- Notification Classes51
- Calendars52
- Common and Specific Alarms52
- Custom Translation Tables52
- Bacnet Router Properties53
- Bacnet Firewall54
- Protocols54
- Xnet54
Local Access to the Carrier® Chillervu55
Communicating through the Local Access Port with a USB Link56
- To Communicate Using Putty57
Troubleshooting60
- Controller Led's60
- Expander Led's61
- To Restore Factory Defaults62
- To Get the Serial Number62
- To Replace the Carrier® Chillervu™'S Battery63
- To Replace the Fuse63
- To Take the Carrier® Chillervu™ out of Service64
Compliance65
- FCC Compliance65
- CE Compliance65
Appendix A: to Identify the Driver in a Carrier® Chillervu™ in the I-Vu® Pro V6.5 Application66
Appendix B: Carrier® Chillervu™ Wire Lists67
- Carrier® Chillervu™ Wire List67
- MPC Open XPIO48 Wire List69
- MPC Open XPIO816 Wire List71
Document Revision History74

Carrier ChillerVu - Mounting the Carrier Chillervu

Table of Contents

Related product manuals