EasyManuals Logo

Cisco 4000 Series User Manual

Cisco 4000 Series
206 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #103 background imageLoading...
Page #103 background image
4-3
Hardware Installation Guide for Cisco 4000 Series Integrated Services Routers
OL-32185-02
Chapter 4 Configure Initial Router Settings on Cisco 4000 Series ISRs
Perform Initial Configuration on Cisco 4000 Series ISRs
Step 6 Enter an enable password that is different from the enable secret password. This password is not
encrypted (and is less secure) and can be seen when viewing the configuration.
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: cisco123
Step 7 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports
other than the console port:
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: cisco
Step 8 Respond to the following prompts as appropriate for your network:
Configure SNMP Network Management? [no]: yes
Community string [public]:
A summary of the available interfaces is displayed.
Note The interface summary includes interface numbering, which is dependent on the router model
and the installed modules and interface cards.
Current interface summary
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1/0 10.10.10.12 YES DHCP up up
GigabitEthernet0/2/0 unassigned YES NVRAM administratively down down
SSLVPN-VIF0 unassigned NO unset up
Any interface listed with OK? value "NO" does not have a valid configuration
Step 9 Respond to the following prompts as appropriate for your network:
Configuring interface GigabitEthernet0/1/0:
Configure IP on this interface? [yes]: yes
IP address for this interface [10.10.10.12]:
Subnet mask for this interface [255.0.0.0] : 255.255.255.0
Class A network is 10.0.0.0, 24 subnet bits; mask is /24
The following configuration command script was created:
hostname myrouter
enable secret 5 $1$t/Dj$yAeGKviLLZNOBX0b9eifO0 enable password cisco123 line vty 0 4
password cisco snmp-server community public !
no ip routing
!
interface GigabitEthernet0/0/0
shutdown
no ip address
!
interface GigabitEthernet0/1/0
no shutdown
ip address 10.10.10.12 255.255.255.0
!
interface GigabitEthernet0/2/0
shutdown

Table of Contents

Other manuals for Cisco 4000 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 4000 Series and is the answer not in the manual?

Cisco 4000 Series Specifications

General IconGeneral
CategoryNetwork Router
Product TypeRouter
Form FactorRack-mountable
Connectivity TechnologyWired
Product FamilyCisco 4000 Series
Operating SystemCisco IOS XE
DimensionsVaries by model
WeightVaries by model
ModelCisco 4000 Series
WAN PortsVaries by model
LAN PortsVaries by model
StorageVaries by model
RedundancyVaries by model
Security FeaturesVaries by model
Network ManagementVaries by model
Data Link ProtocolEthernet, Fast Ethernet, Gigabit Ethernet
Network/Transport ProtocolTCP/IP, UDP
FeaturesVaries by model
InterfacesVaries by model
ModelsVaries
Network InterfacesVaries by model
Power SupplyVaries by model
Virtualization SupportYes

Related product manuals