EasyManuals Logo

Cisco 4000 Series User Manual

Cisco 4000 Series
206 pages
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #206 background imageLoading...
Page #206 background image
A-2
Hardware Installation Guide for Cisco 4000 Series Integrated Services Routers
OL-32185-02
Appendix A Online Insertion and Removal and Hot-Swapping
OIR Procedures
OIR Procedures
The following procedures describe using the OIR process to remove and replace data and voice modules.
Remove a Module
Note Ensure that the module is available before you issue the command to remove it.
From a console terminal run the hw-module subslot <subslot> stop command. The service module
adapter LED blinks, turns off, and the console displays a prompt signaling the module can be removed.
See the following output:
Router# hw-module subslot 2/0 stop
Proceed with stop of module? [confirm]
damo-O2#
*Mar 22 20:43:31.088: %SPA_OIR-6-OFFLINECARD: SPA (SM-X-1T3/E3) offline in subslot 2/0
*Mar 22 20:43:31.088: %IOSXE_OIR-6-SOFT_STOPSPA: SPA(SM-X-1T3/E3) stopped in subslot 2/0,
interfaces disabled
Router# show hw-module subslot 2/0 oir
Module Model Operational Status
------------- -------------------- ------------------------
subslot 2/0 SM-X-1T3/E3 stopped
Insert a Module
You require to run this step only if you run the oir-stop command when the module is not physically
removed from the slot. If the module is physically removed, you do not require to run this command.
From a console terminal issue the hw-module sm {slot} oir-start command. The console displays output
that shows the module change states:
Router# hw-module sm 2 oir-start
Router#
*Nov 11 21:06:17.546: %ATMOC3POM-6-SFP_IN: Interface ATM2/0 OC3 MM SFP has been inserted.
Router#
*Nov 11 21:06:19.442: %LINK-3-UPDOWN: Interface ATM2/0, changed state to up
*Nov 11 21:06:20.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM2/0, changed
state to up
Hot-Swapping Procedures
The following items can be hot-swapped:
Fan trays
Power supplies only when the router is backed up with an RPS
For details of the hot-swapping procedures, see the “Replace a Fan Tray” section on page 5-61 and the
“Remove and Replace Cisco 4000 Series ISRs Power Supplies” section on page 5-40.

Table of Contents

Other manuals for Cisco 4000 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 4000 Series and is the answer not in the manual?

Cisco 4000 Series Specifications

General IconGeneral
CategoryNetwork Router
Product TypeRouter
Form FactorRack-mountable
Connectivity TechnologyWired
Product FamilyCisco 4000 Series
Operating SystemCisco IOS XE
DimensionsVaries by model
WeightVaries by model
ModelCisco 4000 Series
WAN PortsVaries by model
LAN PortsVaries by model
StorageVaries by model
RedundancyVaries by model
Security FeaturesVaries by model
Network ManagementVaries by model
Data Link ProtocolEthernet, Fast Ethernet, Gigabit Ethernet
Network/Transport ProtocolTCP/IP, UDP
FeaturesVaries by model
InterfacesVaries by model
ModelsVaries
Network InterfacesVaries by model
Power SupplyVaries by model
Virtualization SupportYes

Related product manuals