EasyManuals Logo

Cisco ASR-920-12SZ-IM Hardware Installation Guide

Cisco ASR-920-12SZ-IM
118 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #50 background imageLoading...
Page #50 background image
Connecting the Router to the Network, page 80
Prerequisites
Before installing the router, it is important to prepare for the installation by:
Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP).
See Site Planning section.
Unpacking and inspecting the router. See Chassis-Lifting Guidelines section.
Gathering the tools and test equipment required to properly install the router. See Tools and Equipment
section.
For more instructions on how to prepare for the installation of the router, see Preparing for Installation section.
Installing the Router in a Rack
Each Cisco ASR 920 Series Aggregation Services Router router includes rack-mounting brackets. Using the
rack-mounting brackets, you can mount the router in a 19-inch, 23-inch, or an ETSI rack that conforms to the
EIA-310-D specification.
Using the two rack-mounting brackets for mounting, you can recess the router in the equipment rack. This
arrangement provides extra space in front of the router for the cables and allows you to close the doors of
racks equipped with front-close doors.
To attach or replace the rack-mounting brackets, see the Attaching Brackets to the Router section.
The rack-mounting brackets are slotted to allow the router to be mounted in racks with EIA 1.25-inch (3.175-cm)
or WECO 1.0-inch (2.54-cm) hole spacing. When installed in the rack, the router requires one EIA 1.75-inch
(4.4-cm) vertical mounting space (or 1 rack unit [RU]) for mounting (see the Mounting the Router in a Rack
section).
Allow clearance on either side of the router for cooling air to be drawn in through the right side and
circulated through the chassis and out the three-fan exhaust ports mounted on the other side of chassis.
Caution
The sections describe how to install the router in a rack. The procedures in this section apply to both horizontal
and vertical mounting of the router in a rack:
Cisco ASR-920-12SZ-IM Aggregation Services Router Hardware Installation Guide
38
Installing the Cisco ASR 920 Series Router
Prerequisites

Table of Contents

Other manuals for Cisco ASR-920-12SZ-IM

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ASR-920-12SZ-IM and is the answer not in the manual?

Cisco ASR-920-12SZ-IM Specifications

General IconGeneral
DSL WANNo
Ethernet WANYes
Networking standardsIEEE 802.3x
Ethernet LAN data rates10, 100, 1000, 10000 Mbit/s
USB ports quantity2
Ethernet LAN (RJ-45) ports8
Product colorGray
Rack capacity1U
Antenna typeNot supported
AC input voltage100 - 240 V
Power source typeAC, DC, PoE
AC input frequency50 - 60 Hz
Power consumption (typical)130 W
Non-operating altitude0 - 4570 m
Operating temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)5 - 95 %
SafetyUL 60950-1, 2005, CAN/CSA C22.2 No. 60950-1: 2005, IEC 60950-1, 2005, EN 60950-1, 2005, AS/NZS 60950.1:2005
Electromagnetic compatibilityFCC CFR47 Part 15 Class A
Mean time between failures (MTBF)407230 h
Firewall-
Security algorithmsIPSec
Weight and Dimensions IconWeight and Dimensions
Depth286.54 mm
Width444.5 mm
Height44 mm
Weight4830 g

Related product manuals