Cisco Catalyst 2960-X User Manual

PurposeCommand or Action
Enters dynamic authorization local server configuration mode and
specifies a RADIUS client from which a device will accept CoA
and disconnect requests.
client {ip-address | name} [vrf vrfname]
[server-key string]
Step 5
Configures the RADIUS key to be shared between a device and
RADIUS clients.
server-key [0 | 7] string
Example:
Switch(config-sg-radius)# server-key
Step 6
your_server_key
Specifies the port on which a device listens for RADIUS requests
from configured RADIUS clients.
port port-number
Example:
Switch(config-sg-radius)# port 25
Step 7
Specifies the type of authorization the switch uses for RADIUS
clients.
auth-type {any | all | session-key}
Example:
Switch(config-sg-radius)# auth-type any
Step 8
The client must match all the configured attributes for authorization.
(Optional) Configures the switch to ignore the session-key.ignore session-key
Step 9
For more information about the ignore command, see the Cisco
IOS Intelligent Services Gateway Command Reference on
Cisco.com.
(Optional) Configures the switch to ignore the server-key.ignore server-key
Step 10
Example:
Switch(config-sg-radius)# ignore
For more information about the ignore command, see the Cisco
IOS Intelligent Services Gateway Command Reference on
Cisco.com.
server-key
(Optional) Configures the switch to ignore a CoA request to
temporarily disable the port hosting a session. The purpose of
authentication command bounce-port ignore
Example:
Switch(config-sg-radius)# authentication
Step 11
temporarily disabling the port is to trigger a DHCP renegotiation
from the host when a VLAN change occurs and there is no
supplicant on the endpoint to detect the change.
command bounce-port ignore
(Optional) Configures the switch to ignore a nonstandard command
requesting that the port hosting a session be administratively shut
down. Shutting down the port results in termination of the session.
authentication command disable-port ignore
Example:
Switch(config-sg-radius)# authentication
Step 12
Use standard CLI or SNMP commands to re-enable the port.
command disable-port ignore
Catalyst 2960-X Switch Security Configuration Guide, Cisco IOS Release 15.0(2)EX
100 OL-29048-01
Configuring RADIUS
Configuring CoA on the Switch

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g