Cisco Catalyst 2960-X User Manual

DETAILED STEPS
PurposeCommand or Action
Enters the global configuration mode.configure terminal
Example:
Switch# configure terminal
Step 1
Specify the port-channel interface name assigned when
the EtherChannel was created. Enters the interface range
configuration mode.
interface range Interface_name
Example:
Switch(config)# interface Po11
Step 2
Enter the do show interfaces summary command
for quick reference to interface names and types.
Tip
Attaches the IPv6 Snooping policy to the interface or the
specified VLANs on that interface. The default policy is
attached if the attach-policy option is not used.
ipv6 snooping [attach-policy policy_name [ vlan {vlan_ids |
add vlan_ids | except vlan_ids | none | remove vlan_ids | all}
] | vlan [ {vlan_ids | add vlan_ids | exceptvlan_ids | none |
remove vlan_ids | all} ]
Step 3
Example:
Switch(config-if-range)# ipv6 snooping attach-policy
example_policy
or
Switch(config-if-range)# ipv6 snooping attach-policy
example_policy vlan 222,223,224
or
Switch(config-if-range)#ipv6 snooping vlan 222,
223,224
Confirms that the policy is attached to the specified
interface without exiting the configuration mode.
do show running-config interfaceportchannel_interface_name
Example:
Switch#(config-if-range)# do show running-config
int po11
Step 4
How to Attach an IPv6 Snooping Policy to VLANs Globally
Beginning in privileged EXEC mode, follow these steps to attach an IPv6 Snooping Policy to VLANs across
multiple interfaces:
Catalyst 2960-X Switch Security Configuration Guide, Cisco IOS Release 15.0(2)EX
446 OL-29048-01
Configuring IPv6 First Hop Security
How to Attach an IPv6 Snooping Policy to VLANs Globally

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g