Cisco Catalyst 2960-X User Manual

PurposeCommand or Action
Example:
Switch(config)# aaa authentication dot1x
To create a default list that is used when a named list is not
specified in the authentication command, use the default
keyword followed by the method that is to be used in default
situations. The default method list is automatically applied to all
ports.
default group radius
For method1, enter the group radius keywords to use the list of
all RADIUS servers for authentication.
Though other keywords are visible in the command-line
help string, only the group radius keywords are
supported.
Note
Enables 802.1x authentication globally on the switch.dot1x system-auth-control
Example:
Switch(config)# dot1x system-auth-control
Step 4
(Optional) Configures the switch to use user-RADIUS
authorization for all network-related service requests, such as
per-user ACLs or VLAN assignment.
aaa authorization network {default} group
radius
Example:
Switch(config)# aaa authorization network
Step 5
default group radius
(Optional) Specifies the IP address of the RADIUS server.
radius-server host ip-address
Example:
Switch(config)# radius-server host
Step 6
124.2.2.12
(Optional) Specifies the authentication and encryption key used
between the switch and the RADIUS daemon running on the
RADIUS server.
radius-server key string
Example:
Switch(config)# radius-server key abc1234
Step 7
Specifies the port connected to the client that is to be enabled for
IEEE 802.1x authentication, and enter interface configuration
mode.
interface interface-id
Example:
Switch(config)# interface
Step 8
gigabitethernet1/0/2
Catalyst 2960-X Switch Security Configuration Guide, Cisco IOS Release 15.0(2)EX
308 OL-29048-01
Configuring IEEE 802.1x Port-Based Authentication
Configuring 802.1x Port-Based Authentication

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g