Cisco RV042G Administration Guide

VPN
Setting Up a Remote Access Tunnel for VPN Clients (Client To Gateway)
Cisco Small Business RV0xx Series Routers Administration Guide 146
9
always accept compression, even if compression is not enabled. If you
enable this feature for this router, also enable it on the client.
- Keep-Alive: This feature enables the router to attempt to automatically
re-establish the VPN connection if it is dropped. Check the box to enable
this feature, or uncheck the box to disable it.
- AH Hash Algorithm: The AH (Authentication Header) protocol describes
the packet format and default standards for packet structure. With the
use of AH as the security protocol, protection is extended forward into
the IP header to verify the integrity of the entire packet. Check the box to
use this feature. Then select an authentication method: MD5 or SHA1.
MD5 produces a 128-bit digest to authenticate packet data. SHA1
produces a 160-bit digest to authenticate packet data. Both sides of the
tunnel should use the same algorithm.
- NetBIOS Broadcast: NetBIOS broadcast messages are used for name
resolution in Windows networking, to identify resources such as
computers, printers, and file servers. These messages are required by
some software applications and Windows features such as Network
Neighborhood. LAN broadcast traffic is typically not forwarded over a
VPN tunnel. However, you can check this box to allow NetBIOS
broadcasts from one end of the tunnel to be rebroadcast to the other
end.
- Dead Peer Detection (DPD) (available for Tunnel, not Group VPN):
Check the box to enable the router to send periodic HELLO/ACK
messages to check the status of the VPN tunnel. This feature can be
used only when it is enabled on both ends of the VPN tunnel. Specify the
interval between HELLO/ACK messages (how often you want the
messages to be sent).
- NAT Traversal: Network Address Translation (NAT) enables users with
private LAN addresses to access Internet resources by using a publicly
routable IP address as the source address. However, for inbound traffic,
the NAT gateway has no automatic method of translating the public IP
address to a particular destination on the private LAN. This issue
prevents successful IPsec exchanges. If your VPN router is behind a NAT
gateway, check this box to enable NAT traversal. Uncheck the box to
disable this feature. The same setting must be used on both ends of the
tunnel.

Cisco RV042G Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3az, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
Ethernet LAN (RJ-45) ports	6
Routing protocols	IP, RIP-1, RIP-2
Supported network protocols	PPTP, L2TP, IPSec, PPPoE, DHCP
VPN support	PPTP, Layer 2 Tunneling Protocol (L2TP), IPsec, Dead peer detection (DPD), Internet Key Exchange (IKE), split DNS, VPN backup
Firewall security	Stateful packet inspection (SPI) firewall
Security algorithms	3DES, 128-bit AES, 192-bit AES, 256-bit AES, DES, HTTPS, IPSEC
VPN tunnels quantity	50
Authentication method	SHA-1, MD5
MAC address filtering	-
Certification	FCC Class B, CE Class B, UL, cUL, CB
Input current	1 A
Output voltage	12 V
Storage temperature (T-T)	0 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Product color	Black
Rack mounting	No

Weight and Dimensions

Depth	200 mm
Width	130 mm
Height	38.5 mm
Weight	600 g