Contex COUGAR 36 - Default Chapter; Table of Contents

FSG/MTM/001 060511
3
Table of Contents
1. Introduction...........................................................................................................................................10
2. General Description..............................................................................................................................11
2.1 COUGAR 25 AND CHAMELEON 25..................................................................................................... 11
2.2 COUGAR 36, CHAMELEON 36 AND CHAMELEON PREMIER 36................................................... 12
2.2.1 COUGAR 36 and CHAMELEON 36.................................................................................................. 12
2.2.2 CHAMELEON PREMIER 36............................................................................................................. 13
2.3 CHROMA TX 40 AND CRYSTAL TX 40................................................................................................ 13
2.4 MAGNUM XL 54................................................................................................................................... 15
2.5 COUGAR TX 36, CHAMELEON TX 36, PREMIER TX 36................................................................... 16
3. Electrical Check and Adjustments ......................................................................................................25
3.1 MARKING CODES FOR CIRCUIT BOARDS AND PROGRAMMED DEVICES.................................................... 25
3.2 DOWNLOADING SCANNER FIRMWARE ..................................................................................................... 26
3.2.1 Erase and Restore Parameter Blocks................................................................................................. 26
3.3 CHECK AND ADJUSTMENT OF THE SWITCH MODE POWER SUPPLY, SMPS .............................................. 27
3.3.1 AC Voltages........................................................................................................................................ 27
3.3.2 DC Voltages ....................................................................................................................................... 27
3.3.3 Adjustments ........................................................................................................................................ 27
3.3.4 Fuses .................................................................................................................................................. 27
3.3.5 Markings ............................................................................................................................................ 27
3.3.6 Jumper Settings .................................................................................................................................. 27
3.3.7 Hints................................................................................................................................................... 28
3.4 CHECK AND ADJUSTMENT OF LAMP AND MOTOR DRIVER BOARD, LME ................................................ 30
3.4.1 DC Voltages ....................................................................................................................................... 30
3.4.2 Lamp-Driver Adjustment.................................................................................................................... 30
3.4.3 Signal LEDs on the LME-Board ........................................................................................................ 31
3.4.4 Stepper Motor Reference Voltages..................................................................................................... 31
3.4.5 Functional Test................................................................................................................................... 31
3.4.6 Fuses .................................................................................................................................................. 32
3.4.7 Markings ............................................................................................................................................ 32
3.4.8 Jumper Settings .................................................................................................................................. 32
3.4.9 Hints................................................................................................................................................... 32
3.5 CHECK AND ADJUSTMENT OF CAMERA BOARD, CBE (NON TX AND XL MODELS)................................... 35
3.5.1 DC Voltages ....................................................................................................................................... 35
3.5.2 Adjustments ........................................................................................................................................ 35
3.5.3 Functional Test................................................................................................................................... 35
3.5.4 Markings ............................................................................................................................................ 35
3.5.5 Jumper Settings .................................................................................................................................. 35
3.5.6 Hints................................................................................................................................................... 35
3.6 CHECK AND ADJUSTMENT OF CAMERA BOARD, CBF (TX AND XL MODELS) .......................................... 39
3.6.1 DC Voltages ....................................................................................................................................... 39
3.6.2 Adjustments ........................................................................................................................................ 39
3.6.3 Functional Test................................................................................................................................... 39
3.6.4 Markings ............................................................................................................................................ 39
3.6.5 Jumper Settings .................................................................................................................................. 39
3.6.6 Hints................................................................................................................................................... 39
3.7 CHECK OF CONTROLLER BOARD, SUC.................................................................................................... 43
3.7.1 DC Voltages ....................................................................................................................................... 43
3.7.2 Adjustments ........................................................................................................................................ 43
3.7.3 Functional Test................................................................................................................................... 43
3.7.4 Markings ............................................................................................................................................ 43
3.7.5 Switch Settings (Download Control Switches)................................................................................... 43
3.7.6 Jumper Settings .................................................................................................................................. 44
3.7.7 Signal LEDs on the SUC-Board......................................................................................................... 44
3.7.8 Hints................................................................................................................................................... 44
3.8 CHECK OF INTERFACE MODULE, IMB (NON TX AND XL MODELS) .......................................................... 47