Danfoss VLT AutomationDrive FC 302

Option
Name
Description
[47]
Bus ctrl, 0 if timeout
Controls output via bus. The state of the output is set in parameter 5-90 Digital & Relay Bus
Control. If a bus timeout occurs, the output state is set low (off).
[50]
On reference
[51]
MCO controlled
[59]
Remote, enable, no TW
[60]
Comparator 0
See parameter group 13-1* Comparators. If comparator 0 in SLC is true, the output goes high.
Otherwise, it is low.
[61]
Comparator 1
See parameter group 13-1* Comparators. If comparator 1 in SLC is true, the output goes high.
Otherwise, it is low.
[62]
Comparator 2
See parameter group 13-1* Comparators. If comparator 2 in SLC is true, the output goes high.
Otherwise, it is low.
[63]
Comparator 3
See parameter group 13-1* Comparators. If comparator 3 in SLC is true, the output goes high.
Otherwise, it is low.
[64]
Comparator 4
See parameter group 13-1* Comparators. If comparator 4 in SLC is true, the output goes high.
Otherwise, it is low.
[65]
Comparator 5
See parameter group 13-1* Comparators. If comparator 5 in SLC is true, the output goes high.
Otherwise, it is low.
[66]
Comparator 6
See parameter group 13-1* Comparators. If comparator 6 in SLC is true, the output goes high.
Otherwise, it is low.
[67]
Comparator 7
See parameter group 13-1* Comparators. If comparator 7 in SLC is true, the output goes high.
Otherwise, it is low.
[68]
Comparator 8
See parameter group 13-1* Comparators. If comparator 8 in SLC is true, the output goes high.
Otherwise, it is low.
[69]
Comparator 9
See parameter group 13-1* Comparators. If comparator 9 in SLC is true, the output goes high.
Otherwise, it is low.
[70]
Logic rule 0
See parameter group 13-4* Logic Rules. If logic rule 0 in SLC is true, the output goes high. Oth-
erwise, it is low.
[71]
Logic rule 1
See parameter group 13-4* Logic Rules. If logic rule 1 in SLC is true, the output goes high. Oth-
erwise, it is low.
[72]
Logic rule 2
See parameter group 13-4* Logic Rules. If logic rule 2 in SLC is true, the output goes high. Oth-
erwise, it is low.
[73]
Logic rule 3
See parameter group 13-4* Logic Rules. If logic rule 3 in SLC is true, the output goes high. Oth-
erwise, it is low.
[74]
Logic rule 4
See parameter group 13-4* Logic Rules. If logic rule 4 in SLC is true, the output goes high. Oth-
erwise, it is low.
[75]
Logic rule 5
See parameter group 13-4* Logic Rules. If logic rule 5 in SLC is true, the output goes high. Oth-
erwise, it is low.
[76]
Logic rule 6
See parameter group 13-4* Logic Rules. If logic rule 6 in SLC is true, the output goes high. Oth-
erwise, it is low.
[77]
Logic rule 7
See parameter group 13-4* Logic Rules. If logic rule 7 in SLC is true, the output goes high. Oth-
erwise, it is low.
AU275636650261en-000101 / 130R0334212 | Danfoss A/S © 2022.12
Parameter Descriptions
VLT AutomationDrive FC 301/302
Programming Guide