Product Reference Guide I-3
Minimum Increment ........................................................... 1-6
Motion Test......................................................................... 5-3
Motor Timeout.................................................................. 6-15
MSI/Plessey AIM ID........................................................ 6-251
MSI/Plessey Check Character Calculation ....................... 6-248
MSI/Plessey Check Character Transmission..................... 6-250
MSI/Plessey Enable.......................................................... 6-247
MSI/Plessey Fixed Length 1 ............................................. 6-256
MSI/Plessey Fixed Length 2 ............................................. 6-257
MSI/Plessey Label ID....................................................... 6-252
MSI/Plessey Length Control ............................................ 6-253
MSI/Plessey Maximum Label Length............................... 6-254
MSI/Plessey Minimum Label Length ............................... 6-255
MSI/Plessey Number of Check Characters....................... 6-249
MSI/Plessey Stitching....................................................... 6-258
MSI/Plessey........................................................................ F-13
MSI/Plessey.......................................................................... F-9
Normal Operation ............................................................... 3-6
Number of Host Transmission Buffers............................... 6-56
Operating Mode .................................................................. 3-6
Operational Configuration................................................... 3-5
Operational Controls ........................................................... 3-4
Operational Maintenance................................................... 3-10
Operational Modes .............................................................. 3-4
Operational Tests................................................................. 4-1
Operational Verification .................................................... 2-19
Other UPC/EAN Options ............................................... 6-149
PDF417 ............................................................................. F-15
PDF417 ............................................................................... F-9
Pharmacode 39 Check Character Transmission ............... 6-196
Pharmacode 39 Enable..................................................... 6-194
Pharmacode 39 Label ID ................................................. 6-197
Pharmacode 39 Start Stop Character Transmission.......... 6-195
Physical Parameters .............................................................. 1-6
Placing and Installing the Remote Scale Display ................ 2-26
Power Installation ................................................................ 2-9
Power Supply ....................................................................... 1-9
Power-up Beep Control...................................................... 6-21
Power-Up Selftest ................................................................ 4-1
Power-up ............................................................................. 1-7
Power-Up/Selftest & Pre-Operation .................................... 3-4
Power-Up/Selftest ................................................................ 3-4
Pre-Installation Considerations ............................................ 2-2
Preparing the Scanner/Scale for Calibration ......................... 5-4
Price Weight Check ......................................................... 6-151
Productivity Index Reporting (PIR) ................................... 6-47
Programming Overview ....................................................... 6-3
Programming Sequence........................................................ 6-7
Programming Session........................................................... 6-5
Programming via Handheld Device ..................................... 6-3
Programming ....................................................................... 3-7
Proper Scanning Technique ................................................. 3-2
Proper Weighing Technique ................................................ 3-3
Rated Weight Capacity ........................................................ 1-6
Remote Display — Enable/Disable.................................... 6-42
Remote Scale Display Placement/Installation..................... 2-24
Return to Factory Settings.................................................... 6-9
Return to Zero Test ........................................................... 5-12
Return to Zero Test ........................................................... 5-17
RS-232 ACK Character ..................................................... 6-90
RS-232 ACK NAK Enable................................................. 6-88
RS-232 ACK NAK Error Handling ................................... 6-95
RS-232 ACK NAK Retry Count........................................ 6-94
RS-232 ACK NAK Timeout Value.................................... 6-93
RS-232 Baud Rate ............................................................. 6-68
RS-232 Beep After Weigh.................................................. 6-86
RS-232 Beep on ASCII BEL .............................................. 6-85
RS-232 Beep on Not on File.............................................. 6-87
RS-232 Features................................................................. 6-68
RS-232 Hardware Control................................................. 6-76
RS-232 Host Echo Quiet Interval ...................................... 6-81
RS-232 Host Echo............................................................. 6-80
RS-232 Ignore Host Commands........................................ 6-82
RS-232 Intercharacter Delay .............................................. 6-78
RS-232 Interface Selection ................................................. 6-50
RS-232 Label ID Control .................................................. 6-97
RS-232 NAK Character ..................................................... 6-91
RS-232 Number of Data Bits............................................. 6-72
RS-232 Number of Stop Bits ............................................. 6-73
RS-232 Parity .................................................................... 6-74
RS-232 Retry on ACK NAK Timeout ............................... 6-92
RS-232 Single Cable Interface Selection............................. 6-52
RS-232 Software Flow Control .......................................... 6-79
RS-232 TTL Invert............................................................ 6-84
RS-232 TTL ...................................................................... 6-83
RS-232 Wincor-Nixdorf Interface Selection....................... 6-51
RSS Expanded 2D Component Enable............................ 6-173
RSS Expanded AIM ID.................................................... 6-174
RSS Expanded EAN-128 Emulation................................ 6-172
RSS Expanded Enable...................................................... 6-171
RSS Expanded Fixed Length 1......................................... 6-179
RSS Expanded Fixed Length 2......................................... 6-180
RSS Expanded Label ID................................................... 6-175
RSS Expanded Length Control ........................................ 6-176
RSS Expanded Maximum Label Length........................... 6-177
RSS Expanded Minimum Label Length........................... 6-178
RSS Expanded ................................................................... F-14
RSS Expanded ..................................................................... F-2
RSS-14 2D Component Enable ....................................... 6-168
RSS-14 AIM ID............................................................... 6-169
RSS-14 Check Character Transmission............................ 6-166
RSS-14 Enable ................................................................. 6-165
To Next Page
Loading...
Need help?
General
