Denon AVR-1802 Operating Instructions

El
19 TROUBLESHOOTING
If a problem should arisefirst check the following.
1. Are the connections correct 7
2. Have you operated the receiver according to the Operating Instructions 7
3. Are the speakers, turntable and other components operating property 7
If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
Disconnect the power immediately and contact your store of purchase.
Symptom Cause Measures
Page
DISPLAY not lit and sound not produced
l Power cord not plugged in securely.
l Check the insertion of the power cord plug.
9
when power switch set to on.
l Turn the power off with the remote control
25
unit after turning the POWER operation
switch on.
l Speaker cords not securely connected.
l Connect securely.
14,15
l Improper position of the audio function
l Set to a suitable position.
26
2
button.
-ci
2%
DISPLAY lit but sound not produced. l Volume control set to minimum.
l Turn volume up to suitable level.
27
.p 3-
D
l MUTING is on. l Switch off MUTING.
28
CI
l Digital signals not input Digital input
l Input digital signals or select input jacks to
27
$42
selected. which digital signals are being input.
z-m
CF
5;
l Speaker terminals are short-circuited.
l Switch power off, connect speakers
14,15
PO
properly, then switch power back on.
:s s
l Block the ventilation holes of the set.
l Turn off the set’s power, then ventilate it
5, 15
G ti
DISPLAY not displayed and the
well to cool it down.
“is
Es
“ON/STANDBY” LED flashes at a high
Once the set is cooled down, turn the
5 $
rate
power back on.
l The unit is operating at continuous high
l Turn off the set’s power, then ventilate it
5, 15
F$
power conditions and/or inadequate
well to cool it down.
g-
ventilation. Once the set is cooled down, turn the
power back on.
00
0
l Incomplete connection of speaker cords.
l Connect securely.
14,15
Sound produced only from one channel.
l Incomplete connection of input/output
l Connect securely.
9 - 14
cords.
Positions of instruments reversed during
l Reverse connections of left and right
l Check left and right connections.
14
stereo playback.
speakers or left and right input/output
cords.
.+z
3 l Batteries dead.
l Replace with new batteries.
16
E
l Remote control unit too far from this unit.
l Move closer.
16
+G
This unit does not operate properly when l Obstacle between this unit and remote
l Remove obstacle.
16
8
remote control unit is used. control unit.
4
l Press the proper button.
-
E
l Different button is being pressed.
l 8 and 0 ends of battery inserted in reverse.
l Insert batteries properly.
16
d
Note:
When a subwoofer has been connected and the virtual surround function is being used, the signal played from the subwoofer channel is LFE
only (only when playing Dolby Digital or DTS signals) for initial factory settings (i.e., the setting of the front speaker is “LARGE” and the setting
of the subwoofer mode is “NORM”).
When subwoofer effects are felt to be weak, while in the system setup mode try setting the subwoofer mode to “+MAIN”, or the front speaker
to “SMALL” in the Speaker Configuration settings.
Making these settings will result in the low-frequency sounds of the front channel being played from the subwoofer.
47

Denon AVR-1802 Specifications

General

Speakers connectivity type	-
Receiver type	Surround
Frequency range	10 - 100000 Hz
Audio output channels	5.1 channels
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.7 %
Power output per channel (1KHz@6 Ohm)	115 W
Power output per channel (20-20KHz@8 Ohm)	80 W
AC input voltage	120 V
AC input frequency	60 Hz
Equalizer	Yes
Audio decoders	DTS, Dolby Digital, Dolby Pro Logic II
3D	No
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
HDMI in	0
Composite video in	5
S-Video inputs quantity	4
Digital audio coaxial in	1
Digital audio optical in	3

Weight and Dimensions

Depth	417 mm
Width	434 mm
Height	171 mm
Weight	10900 g