DGSHAPE monoFab SRM-20 User Manual

Guide for Cutting
with MODELA Player 4
Guide for Cutting
with SRP Player
Preparing the Machine
Double Sided Cutting Manual
 This manual provides basic instructions on how to perform double-sided
cutting using one of the two included software programs: SRP Player and
MODELA Player 4. For information on any use of SRP Player or MODELA
Player 4 not covered herein, see the Help for each software program.
" User’s Manual “Display Help Dialog”
 For information on basic operation, one-sided cutting, maintenance, and
other procedures, refer to the User’s Manual.

DGSHAPE monoFab SRM-20 Specifications

General

Brand	DGSHAPE
Model	monoFab SRM-20
Category	Cutter
Language	English

Summary

Preparing the Machine

Flow Diagram

Overview of the machine preparation steps.

STEP 1: Turning the Power On

Procedure for powering on the machine.

STEP 2: The Machine Run-in

Instructions for the initial run-in process of the machine.

STEP 3: Confirm the Command Set

Verifying the command set selection for machine operation.

STEP 4: Register the Cutting Tool

Registering cutting tools within the SRP Player software.

STEP 5: Attach the Cutting Tool

Procedure for physically attaching the cutting tool to the machine.

Guide for Cutting with SRP Player

The Flow of Double-Sided Cutting

Outlines the workflow for performing double-sided cutting.

Items Necessary for Cutting

Lists required software and machine accessories for cutting.

Items to Prepare Yourself

Details materials and tools the user needs to provide.

STEP 1: Attach the Material to the Scrap Board

Attaching the workpiece material to the scrap board.

STEP 2: Install the Cutting Tool

Procedure for installing the cutting tool into the machine.

STEP 3: Set the Origin Point

Setting the X, Y, and Z origin points for cutting.

STEP 4: Level the Scrap Board Surface

Adjusting the scrap board surface for flatness.

STEP 5: Perform the Surface Leveling of the Material

Leveling the surface of the workpiece material.

STEP 6: Level the Bottom Surface of the Material

Leveling the bottom surface of the workpiece material.

STEP 1: Measure the Thickness of the Material

Measuring the thickness of the material using calipers.

STEP 2: Determine the Size and Orientation of the Model

Setting the model's size and orientation in the software.

STEP 3: Determine What to Do

Selecting processing options and configurations.

STEP 4: Create the Cutting Data

Generating tool paths and cutting data.

STEP 5: Preview the Result of Cutting

Simulating and previewing the cutting outcome.

STEP 1: Set the Origin Point

Setting the origin point for the double-sided cutting process.

STEP 2: Perform the Roughing

Executing the roughing cut for the model.

STEP 3: Perform the Finishing

Executing the finishing cut for detailed portions.

STEP 4: Set the Drilling Process

Configuring the drilling process for positioning holes.

STEP 5: Drill the Scrap Board

Drilling holes into the scrap board for alignment.

STEP 6: Reverse the Material

Repositioning the material using alignment pins.

STEP 7: Cut the Bottom Surface

Performing the cutting operation on the second side.

STEP 8: Remove the Cut Material

Safely removing the finished workpiece.

STEP 9: Turning the Power Off

Procedure for safely powering down the machine.

Guide for Cutting with MODELA Player 4

The Flow of Double-Sided Cutting

Outlines the workflow for performing double-sided cutting.

The Flow of One Side Cutting

Outlines the workflow for performing one-sided cutting.

Items Necessary for Cutting

Lists required software and machine accessories for cutting.

Items to Prepare Yourself

Details materials and tools the user needs to provide.

STEP 1: Load the Cutting Data

Importing design files into MODELA Player 4.

STEP 2: Set the Machine Selection

Configuring the machine and printer settings.

STEP 3: Set the Origin Point of the Model and Orientation

Setting the model's origin and orientation in the software.

STEP 4: Set the Material

Specifying the type and quality of the material.

STEP 5: Set the Number of Cutting Surfaces

Defining the number of surfaces to be cut.

STEP 6: Set the Margin

Setting approach paths around the model.

STEP 7: Set the Surface leveling Process of the Scrap Board

Configuring the leveling process for the scrap board.

STEP 8: Confirm the Cutting Preview

Reviewing the cutting path and simulation.

STEP 9: Set the Surface leveling Process of the Material

Configuring the leveling process for the workpiece material.

STEP 10: Set the Roughing Process

Setting up the roughing cut parameters.

STEP 11: Set the Finishing Process

Setting up the finishing cut parameters for detail.

STEP 12: Set the Drilling Process

Configuring the drilling process for positioning holes.

STEP 13: Set the Bottom Surface Process

Configuring the cutting process for the bottom surface.

Cutting (Double Sided)

Performing the actual double-sided cutting process.