EC-PACK EC-JET 1000Pro

To Next Page

To Previous Page

Guangzhou EC-PACK Packaging Equipment Co., Ltd.

EC-JET 1000Pro Continuous Inkjet Printer

8. EC-JET Agents or resellers will send the machine back to customer. Follow

above opposite steps to change the SMART bottles into ink and solvent tank, then you

can use the printer normally.

Main Page

Copyright Notice1
Disclaimer1
About this Manual1
Table of Contents2
Safety8
Warnings and Cautions8
Lethal Voltages8
Operation9
Inks and Solvents9
First Aid10
Eye Contact10
Skin Contact10
Inhalation10
Ingestion10
In Case of Emergency10
Noise Emissions10
Introduction11
Printer System Overview11
System Description12
Operating Simplicity12
Diagnostics12
Print Head Design12
Printing Drops12
Leaving Gaps12
Detecting Products13
Conveyor Speed13
Ink Blockage Prevention13
Blockages13
Automatic Cleaning at Shutdown13
Velocity of Drop14
Principles of Operation15
Controls and Indicators16
Getting Started16
Installation16
Connection17
Switch on the Printer17
Start and Stop Keys18
Screen Display19
Display Brief Introduction20
Cursor Control Keys21
Text Control Keys21
General Control Keys21
Creating a Simple Message22
Advanced Editing Features24
Moving to Pixel (Drop) Locations24
Moving to the Beginning of Message24
Quick Shifting the Character Font or New Line24
Quick Selecting the Message with Arrows Key25
Copying and Pasting the Message25
Starting the Printer25
Stopping (Switching Off) the Printer25
Passwords26
Screen Calibration26
Using the System27
Moving Around the Menus27
Selecting Menus27
Select and Edit28
Current Message Screen28
Editing a Message29
Checking the Current Status of the Printer30
System Status Line30
Print Status Screen30
Checking the Printer Status30
Listing Error Messages31
Password32
Password Level32
Password33
Creating, Editing and Deleting Message Fields34
Introduction34
The Message Used Has a Complete MIX of All Field Types34
Message Fields35
Editing and Deleting Message Fields36
Editing Fields36
Text Fields36
Other Fields37
Deleting Fields37
Creating Text Fields37
Creating Date Fields37
Creating Sequential Number Fields41
Creating Time Fields43
Creating Timed Message Fields45
Creating Remote Fields49
Creating Logo Fields50
Logo Editor51
Changing the System Setup52
Adjusting Ref. Information53
Print Height53
Scale Height53
Print Width53
Print Delay53
Print Interval53
Print Count53
Reverse Message (Vertical)53
Reverse Message (Horizontal)53
Bold Ratio54
Aux in54
Photocell54
Shaft Encoder54
Repeated Trigger54
Alarm Set up54
Changing the Installation Setup55
Set Time55
Set Date55
Conduit Length55
Head Height56
Meter Counter56
Changing System Set up56
Print Head Code56
Ref. Modulation56
Ink Selection57
Password57
Change Password57
Change Language57
Remote Setup Menu57
Diagnostic Menu57
Solvent Add Time58
Diagnostics59
Start Jet59
Stop Jet60
Quick Start Jet60
Start Print60
Stop Print60
Clear Nozzle61
Flush Nozzle61
Flush Shut down61
Monitor Jet62
System Times (System Timing Information)63
System Configuration Information63
Set Pressure64
Filter Purge64
Real-Time Switch or Edit Message65
Real-Time Switch Message65
Real-Time Edit Message65
Real-Time New Message65
Routine Maintenance66
Cleaning the Printer Cabinet66
General66
Ink Spillages66
Cleaning the Nozzle66
Cleaning the Print Head66
Replenishing Ink and Solvent67
Note67
EC1000 Consumable Verification68
Refilling the Ink or Solvent71
Cleaning/Replacing the Air Filter72
Cleaning and Replacement of Air Inlet Filter72
Cleaning/Replacing the Air Outlet Filter73
Quick Maintenance Mode74
Warning and Fault Messages77
Summary of Warning Messages77
System Failures77
Print Failures77
System Warnings77
System Failures78
Print Failures78
Print Head Temperature79
Deflector Voltage79
Charge80
Velocity of Drop80
Power Supply80
Temperature/Deflector80
Ink Tank Empty80
Internal Spillage Fault81
System Warnings81
No VOD Adjustments82
Jet Shut down Incomplete82
Over Speed (Print Go)82
Ink Low83
Solvent Low83
Print Go / Remote Data83
Service Time83
Print Head Cover off83
Bad Print Head Code84
New Print Head Fitted84
Charge Calibration Range84
Safety Override Detected84
Low Pressure84
Over Speed (Variable Data)85
Default Language85
There Is Little Chance of Fault of Default Language85
Memory Failure85
Memory Corrupt85
No Message Stored in Memory85
Troubleshooting86
Where to Start86
Identifying Faults87
Identifying Faults by Print Sample87
Identifying Faults by Symptom88
Problem Solving90
Problem Solving - Print Samples91
Problem Solving - Ink System Mechanical Faults93
Problem Solving - Printhead Mechanical Faults94
Blockage Caused by Knocking and Strong Vibration100
Appendix 1：Installation & Setting up103
Unpacking the System103
Where to Put the Printer103
Accessories103
Power Connection104
Attaching the Printhead to the Production Line104
Print Height104
Setting up the Photocell105
Photocell Connections105
Setting up the Shaft Encoder106
Shaft Encoder Connections106
Selecting the Encoder, Gearing, and Print Width107
Encoder and Print Width Problems111
Using the Printer Alarm Output112
Filling with Ink and Solvent112
Purging (or Priming) the Filters113
Appendix 2：Technical Specification114
Introduction114
Technical Data114
Cabinet114
Dimensions114
Weight114
Power Requirements114
Environmental114
Ink System115
Construction115
Capacity115
Pressure115
Level Control115
Performance115
Memory Capacity115
Printhead115
Types115
Dimensions116
Throw Distance (Recommended)116
Printing Performance Data116
Raster Information116
Character Height Range116
Certificate Acquired117
Emc117
Lvd118
Appendix 3: Printable Line Speeds119
Ideal Pitch119
Double Pitch119
Triple Pitch119
Appendix 4: Dimension Layout120

EC-PACK EC-JET 1000Pro - Page 76

Table of Contents