ELTEX MES3108 User Manual

MES3000 Ethernet switch series 193
Interface Configuration Mode Commands
Command line request in the interface configuration mode appears as follows:
console(config-if)#
Table 5.235 Commands of interface configuration for Ethernet interface and a group of ports
Command
Value/Default Value
Action
[no] pppoe
intermediate-agent
-
Enables/disables PPPoE Intermediate Agent for the interface.
[no] pppoe
intermediate-agent
format-type circuit-id
circuit_id
circuit_id: a string of 1–63
characters
Assigns the circuit_id identifier added by the switch. The identifier
specified in the command completely overrides the identifier
which was calculated based on the access-node-id and
option/delimiter global parameters. The command in negative
form restored settings specified by the access-node-id and
option/delimiter global parameters.
[no] pppoe
intermediate-agent
format-type remote-id
remote_id
remote_id: a string of 1–63
characters
MAC address of the switch
is used as remote-id by
default.
Assigns the remote-id identifier added by the switch. The identifier
should be configured in all switch interfaces with PPPoE IA. The
command in negative form restores the default setting.
[no] pppoe
intermediateagent
timeout [timeout]
timeout : (0..600)/600
seconds
Sets client session timeout. Timeout of new session is infinity
when timeout is set as 0.
The negative form of the command restores the default setting
[no] pppoe
intermediate-agent trust
The interface is not trusted
by default.
Makes an interface trusted/untrusted. Command
adds or removes an interface to/from the list of trusted interfaces.
Interfaces with connected PPPoE servers are configured as
trusted. Interfaces with connected users are configured as
untrusted. The command in negative form restores the default
setting.
[no] pppoe
intermediate-agent
vendor-tag strip
Removal is disabled by
default.
Enables/disables removal of a vendor-specific option from PADO,
PADS, PADT packets before they are sent to user. The removal
option can be used only in the interface which has PPPoE IA
enabled and is trusted. The removal option is normally configured
in the PPPoE server interface
The command in negative form disables the removal mode.
EXEC Mode Commands
Command line request in the EXEC mode appears as follows:
console#
Table 5.236 EXEC mode commands
Command
Value/Default Value
Action
show pppoe
intermediateagent info
[interface {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel
group}]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4)
group: (1..24)
Displays settings of PPPoE Intermediate Agent. If the
command does not explicitly specify an interface, it is
performed for all interfaces with enabled PPPoE IA and trusted
ports.
show pppoe
intermediateagent statistics
[interface {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel
group}]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4)
group: (1..24)
Displays statistics of PPPoE Intermediate Agent. If the
command does not explicitly specify an interface, it is
performed for all interfaces with enabled PPPoE IA and trusted
ports.
clear pppoe
intermediateagent statistics
[interface {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel
group}]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4)
group: (1..24)
Clears statistics of PPPoE Intermediate Agent. If the command
does not explicitly specify an interface, it is performed for all
interfaces with enabled PPPoE IA and trusted ports.

ELTEX MES3108 Specifications

General

Brand	ELTEX
Model	MES3108
Category	Switch
Language	English