Chapter 2. API Reference
(continued from previous page)
TEMP_SENSOR_CAL (BLOCK2) Temperature calibration ␣
,→ = -9.200000000000001 R/W (0b101011100)
ADC1_MODE0_D2 (BLOCK2) ADC1 calibration 1 ␣
,→ = -28 R/W (0x87)
ADC1_MODE1_D2 (BLOCK2) ADC1 calibration 2 ␣
,→ = -28 R/W (0x87)
ADC1_MODE2_D2 (BLOCK2) ADC1 calibration 3 ␣
,→ = -28 R/W (0x87)
ADC1_MODE3_D2 (BLOCK2) ADC1 calibration 4 ␣
,→ = -24 R/W (0x86)
ADC2_MODE0_D2 (BLOCK2) ADC2 calibration 5 ␣
,→ = 12 R/W (0x03)
ADC2_MODE1_D2 (BLOCK2) ADC2 calibration 6 ␣
,→ = 8 R/W (0x02)
ADC2_MODE2_D2 (BLOCK2) ADC2 calibration 7 ␣
,→ = 12 R/W (0x03)
ADC2_MODE3_D2 (BLOCK2) ADC2 calibration 8 ␣
,→ = 16 R/W (0x04)
ADC1_MODE0_D1 (BLOCK2) ADC1 calibration 9 ␣
,→ = -20 R/W (0b100101)
ADC1_MODE1_D1 (BLOCK2) ADC1 calibration 10 ␣
,→ = -12 R/W (0b100011)
ADC1_MODE2_D1 (BLOCK2) ADC1 calibration 11 ␣
,→ = -12 R/W (0b100011)
ADC1_MODE3_D1 (BLOCK2) ADC1 calibration 12 ␣
,→ = -4 R/W (0b100001)
ADC2_MODE0_D1 (BLOCK2) ADC2 calibration 13 ␣
,→ = -12 R/W (0b100011)
ADC2_MODE1_D1 (BLOCK2) ADC2 calibration 14 ␣
,→ = -8 R/W (0b100010)
ADC2_MODE2_D1 (BLOCK2) ADC2 calibration 15 ␣
,→ = -8 R/W (0b100010)
ADC2_MODE3_D1 (BLOCK2) ADC2 calibration 16 ␣
,→ = -4 R/W (0b100001)
Config fuses:
DIS_RTC_RAM_BOOT (BLOCK0) Disables boot from RTC RAM ␣
,→ = False R/W (0b0)
DIS_ICACHE (BLOCK0) Disables ICache ␣
,→ = False R/W (0b0)
DIS_DCACHE (BLOCK0) Disables DCache ␣
,→ = False R/W (0b0)
DIS_DOWNLOAD_ICACHE (BLOCK0) Disables Icache when SoC is in␣
,→Download mode = False R/W (0b0)
DIS_DOWNLOAD_DCACHE (BLOCK0) Disables Dcache when SoC is in␣
,→Download mode = False R/W (0b0)
DIS_FORCE_DOWNLOAD (BLOCK0) Disables forcing chip into␣
,→Download mode = False R/W (0b0)
DIS_CAN (BLOCK0) Disables the TWAI Controller␣
,→hardware = False R/W (0b0)
DIS_BOOT_REMAP (BLOCK0) Disables capability to Remap RAM␣
,→to ROM address sp = False R/W (0b0)
ace
FLASH_TPUW (BLOCK0) Configures flash startup delay␣
,→after SoC power-up, = 0 R/W (0x0)
unit is (ms/2). When the value is␣
,→15, delay is 7.
5 ms
DIS_LEGACY_SPI_BOOT (BLOCK0) Disables Legacy SPI boot mode ␣
,→ = False R/W (0b0)
UART_PRINT_CHANNEL (BLOCK0) Selects the default UART for␣
,→printing boot msg = UART0 R/W (0b0)
(continues on next page)
Espressif Systems 811
Submit Document Feedback
Release v4.4
To Next Page
Loading...