Fargo HDP5000 User Manual

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP5000 High Definition Card Printer/Encoder User Guide (Rev. 1.3)
vii
Using the LRC Generation dropdown list _____________________________________________ 8-75
Using the Encoding Mode dropdown list ______________________________________________ 8-76
Reviewing the ISO Track Locations__________________________________________________ 8-77
Sending the Track Information______________________________________________________ 8-78
Reviewing the Sample String _______________________________________________________ 8-79
Reviewing the ASCII Code and Character Table________________________________________ 8-80
Using the Default button (Image Transfer tab)__________________________________________ 8-81
Using the Lamination tab (HDP5000-LC) ________________________________________8-82
Selecting the Lamination Position ___________________________________________________ 8-83
Adjusting the Lamination Speed - Transfer Dwell Time __________________________________ 8-84
Selecting the Lamination Side dropdown menu_________________________________________ 8-85
Reviewing the Card Lamination Module Unit table (No Flipper versus Flipper) _______________ 8-86
Selecting the Lamination Type______________________________________________________ 8-87
Adjusting the Lamination Temperature _______________________________________________ 8-89
Selecting the Defaults button _______________________________________________________ 8-90
Using the K Panel Resin tab____________________________________________________8-91
Using the Scroll controls __________________________________________________________ 8-92
Using the Click and Drag capability__________________________________________________ 8-93
Selecting “inches or mm” radio button________________________________________________ 8-93
Using the Add and Delete buttons ___________________________________________________ 8-93
Selecting the Full Card ____________________________________________________________ 8-94
Selecting the Defined Area(s)_______________________________________________________ 8-95
Selecting the Undefined Area(s)_____________________________________________________ 8-96
Defining the Area to activate the Card Grid____________________________________________ 8-97
Measuring the Total Card area ______________________________________________________ 8-98
Measuring the Area to be positioned on the Card________________________________________ 8-99
Selecting the Print YMC under the K and Print K Only options ___________________________ 8-100
Using the Printer Supplies tab _________________________________________________8-102
Reviewing Information on the Supplies tab ___________________________________________ 8-103
Section 9: Toolbox_________________________________________________________9-1
Accessing the Toolbox _______________________________________________________________ 9-1
Selecting the Configuration tab_________________________________________________________ 9-2
Using the Configuration Tab___________________________________________________________ 9-3
Using the Optional Printer Features Group Box__________________________________________ 9-3
Using the Event Monitoring Group Box __________________________________________________ 9-4
Reviewing the Ribbon Low message __________________________________________________ 9-4
Reviewing the Laminate Low Message ________________________________________________ 9-5
Using the Film Low message ________________________________________________________ 9-6
Selecting the Set Language for Printer LCD Display Group Box ____________________________ 9-6
Selecting the Calibrate Laminator tab____________________________________________________ 9-7
Selecting the Calibrate Film tab ________________________________________________________ 9-8
Selecting the Calibrate Ribbon tab ______________________________________________________ 9-9
Selecting the Clean Printer tab ________________________________________________________ 9-10
Using the Clean Printer Group Box __________________________________________________ 9-12
Selecting the Advanced Settings tab ____________________________________________________ 9-13
Using the Image Darkness Option ___________________________________________________ 9-15
Using the Print Top of Form Option__________________________________________________ 9-16
Using the Print Left of Form Option _________________________________________________ 9-18
Using the Mag Top of Form Option__________________________________________________ 9-19
Using the Print Flip Angle Option ___________________________________________________ 9-21
Using the Print Flip Level Option ___________________________________________________ 9-21
Using the Encoder Flip Angle Option ________________________________________________ 9-21
Setting the Printhead Resistance_____________________________________________________ 9-21

Fargo HDP5000 Specifications

General

Maximum resolution	300 x 300 DPI
Print speed (color)	7 card/h
Print speed (monochrome)	14 card/h
Product color	Black
Internal memory	16 MB
Total input capacity	100 sheets
Compatible operating systems	Windows 2000 / XP / Server 2003 / Vista (32 bit) Mac OS X v10.4 / v10.5 Linux

Weight and Dimensions

Weight	7300 g
Dimensions (WxDxH)	313 x 235 x 292 mm