Name: Fargo HDP5000
Brand: Fargo
Rating: 5 (1 reviews)

To Next Page

To Previous Page

RESTRICTED USE ONLY Fargo Electronics, Inc.

HDP5000 High Definition Card Printer/Encoder User Guide (Rev. 1.3)

viii

Using the Transfer TOF Adjustment Option ___________________________________________ 9-22

Using the Transfer Temp Offset Option_______________________________________________ 9-25

Print Tension Settings _______________________________________________________________ 9-25

Using the Ribbon Print Takeup Tension Option_________________________________________ 9-25

Using the Film Print Takeup Tension Option___________________________________________ 9-25

Using the Ribbon Print Supply Tension Option_________________________________________ 9-26

Transfer Tension Settings ____________________________________________________________ 9-27

Using the Film Supply Transfer Tension Option ________________________________________ 9-27

Using the Film Takeup Transfer Tension Option________________________________________ 9-27

Using the Resin Heat Adjust Option__________________________________________________ 9-28

Using the Sleep Time Option _______________________________________________________ 9-28

Using the Standby Time Option _____________________________________________________ 9-28

Using the Blush Point Option_______________________________________________________ 9-28

Using the LCD Contrast Option _____________________________________________________ 9-29

Using the Cleaning rate Option _____________________________________________________ 9-30

Using the EAT Disable Option______________________________________________________ 9-30

Using the Film Print Cooling Level Option ____________________________________________ 9-30

Using the Film Transfer Cooling Level Option _________________________________________ 9-30

Using the Enable Ribbon Wrinkle Compensation Option _________________________________ 9-30

Using the Lamination Top of Form Option ____________________________________________ 9-30

Using the Lamination End of Form Option ____________________________________________ 9-30

Using the Lamination Bottom Takeup Option __________________________________________ 9-30

Using the Lamination Top Takeup Option_____________________________________________ 9-30

Using the Lamination Card Backup Option ____________________________________________ 9-31

Using the lamination Card Length Option _____________________________________________ 9-31

Reviewing the No Printer Connected error message _____________________________________ 9-31

Reviewing the Value outside the Range error message ___________________________________ 9-31

Section 10: Cleaning______________________________________________________10-1

Using the Required Supplies__________________________________________________________ 10-1

Safety Messages (review carefully)_____________________________________________________ 10-2

Accessing the Clean Printer tab________________________________________________________ 10-3

Cleaning the Printer Platen Roller and Card Feed Rollers _________________________________ 10-3

Cleaning Procedures ________________________________________________________________ 10-5

Cleaning inside the Printer _________________________________________________________ 10-5

Cleaning outside the Printer ________________________________________________________ 10-5

Cleaning the Printhead ____________________________________________________________ 10-6

Replacing the Card Cleaning Roller__________________________________________________ 10-7

Cleaning the Magnetic Encoder _____________________________________________________ 10-8

Section 11: Fargo Workbench Printer Utility __________________________________11-1

Reviewing the Card tab and Diagnostic button _________________________________________ 11-1

Configuring Data (F-Panel for YMCFK Ribbon) __________________________________11-3

Section 12: Packing the Card Printer ________________________________________12-1

Section 13: Firmware Updates ______________________________________________13-1

Performing the Firmware Updates ___________________________________________________ 13-1

Section 14: Fargo Technical Support ________________________________________14-1

Contacting Fargo Technical Support____________________________________________________ 14-1

Reading the Serial Numbers on a Fargo Printer ___________________________________________ 14-2

Finding out when a Fargo Card Printer was manufactured ________________________________ 14-2

Reviewing Example No. 1: Serial Number A1280224 ___________________________________ 14-2

Section 15: Reviewing Spare Parts Lists ______________________________________15-1

Reviewing Spare Parts List for HDP5000 and HDP5000-LC ______________________________ 15-1

Maximum resolution	300 x 300 DPI
Print speed (color)	7 card/h
Print speed (monochrome)	14 card/h
Product color	Black
Internal memory	16 MB
Total input capacity	100 sheets
Compatible operating systems	Windows 2000 / XP / Server 2003 / Vista (32 bit) Mac OS X v10.4 / v10.5 Linux

Weight	7300 g
Dimensions (WxDxH)	313 x 235 x 292 mm

Fargo HDP5000 User Manual

Table of Contents

Other manuals for Fargo HDP5000

Questions and Answers:

Fargo HDP5000 Specifications

Related product manuals