Flexball Series 3500 - User Manual

Flexball Italiana S.r.l. 1
O
O
p
p
e
e
r
r
a
a
t
t
i
i
n
n
g
g
m
m
a
a
n
n
u
u
a
a
l
l
&
&
m
m
o
o
u
u
n
n
t
t
i
i
n
n
g
g
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s

Summary

Pilot Instructions

Acquiring System Command

Explains the procedure for acquiring system control from any command station.

Emergency Lever Operation

Provides instructions for operating the system manually in emergency situations.

Command Station Management

Command Station Programming

Guides on configuring the command station based on system setup (motors, actuators).

Actuator System Details

Accessories and Options

Trim;Flap Option Operation

Explains how to activate Trim/Flap commands from the command station.

System Types and Installation Schemes

Installation Scheme A (2 Mechanical Actuators)

Illustrates installation scheme A for 2 mechanical actuators and up to 3 command stations.

Installation Scheme B (2 Mechanical Actuators)

Presents installation scheme B for 2 mechanical actuators and up to 3 command stations.

Installation Scheme C (2 Mechanical Actuators)

Details installation scheme C for 2 mechanical actuators at CANBus network ends.

Installation Scheme D (1 Actuator)

Shows installation scheme D with 1 actuator at one end of the CANBus network.

Installation Scheme E (1 Actuator)

Illustrates installation scheme E with 1 actuator in the middle of the CANBus line.

CANBus Network Configuration

Command Station Configuration

Explains how to configure command stations using dip-switches for address and termination.

Actuator Configuration

Details configuring actuators for end-line resistance and CANBus address.

Push-Pull Cable Installation

Standard Push-Pull Cable Mounting

Details the mounting procedure for standard push-pull cables.

Electrical Installation and Wiring

Actuator Output Cable Wiring

Details wiring of actuator output cables, focusing on supply connector and motor cables.

Single Motor System Wiring

Provides electrical schematics for 1 motor systems with varying dashboard configurations.

Two Motor System Wiring

Shows electrical schematics for 2 motor systems with 1 or 2 actuators.

Outgoing Cable Wiring for Propulsion Types

Details electrical cabling for actuator outgoing cables for mechanical and hybrid systems.

Electronic Propulsion Cabling

Provides cabling instructions for electronic propulsion systems and gearbox/trim connections.

Actuator Programming and Setup

Actuator Parameters Overview

Setting Push-Pull Cable Strokes

Mechanical Motor;Gearbox Programming

Mechanical System Specific Parameters

Electronic Motor and Gearbox Programming

Electronic Motor;Mechanical Gearbox Strokes

Electronic Motor;Mechanical Gearbox Parameters

Parameter A0 Adjustment

Voltage Output for Electronic Motors

Mechanical Motor & Electronic Gearbox Setup

Push-Pull Cable & Throttle Strokes

Electronic Gearbox Specific Parameters

Electronic Motor & Electronic Gearbox Setup

Specific Parameters for Electronic Systems

CANBus Motor & Mechanical Gearbox Setup

Push-Pull Cable & Stroke Programming

CANBus Specific Parameters

CANBus Parameter Value Setting

Guides on setting CANBus parameter values for different motor types.

FPT Motor CANBus Connection

CANBus Motor & Electronic Gearbox Setup

Trim or Flap Command Option

Hybrid Motors Option Programming

System Failure Behavior and Troubleshooting

Unforeseen Motor Switching Off

Electrical Network Faults

Overload;Cable Break Protection

Details the actuator's protection against overload or push-pull cable issues.

Troubleshooting Common Issues

Provides a table of common irregularities and checks for troubleshooting.

Command Station LED Diagnosis

Flexball Series 3500 Specifications

General

Brand	Flexball
Model	Series 3500
Category	Control Unit
Language	English