Flexball Series 3500 - Electrical Installation of Systems with 1 Motor, 1 Actuator and 2 Dashboards

69 pages

Save Page as PDF

To Next Page

To Previous Page

Flexball Italiana S.r.l. 44

10.1.4. Electrical installation of systems with 1 motor, 1 actuator and 2

dashboards

Vdc

GND

Flexball

actuator

Vdc batteria

Vdc battery

GND - Motore

GND - Engine

Key Ignition - Deck

Sottochiave - Plancia

Key Ignition - Fly bridge

Sottochiave - Fly bridge

For the detailed list of components, please refer to the table at section 10.1.2.

Main Page

Default Chapter2
- Table of Contents2
1 Introduction4
2 General Installation Features4
- Description of the System and Its Parts4
- Maximum Extension of the System4
- System Performance4
3 Pilot Instructions5
- Control Keypad6
- Acquisition of the Command7
- Engine Warm-Up7
- Synchro Mode8
- Fast Start-Up Mode8
- Emergency Lever8
4 Command Station9
- Dimensions9
- Command Station Series 35009
- Command Station Series 450010
- Friction Adjustment10
- Command Station Series 350010
- Command Station Series 450011
- Programming of the Command Station11
- Command Station Label12
- Command Station Codes12
5 Actuator13
- Drawing of Actuators with Mechanical Interface13
- Drawing of Full Electronic Actuator14
- Actuator Labels15
- Actuator Codes16
- Electronic Actuator Boards17
- Actuator Board Ver. 3.117
- Relays PCB Version 1.0 for Electronic Gearboxes18
- Relays PCB Version 2.0 for Electronic Gearboxes19
- Canbus PCB for Motor with Canbus Interface20
- Galvanic Insulation PCB for Analogue Voltage Signals20
6 Accessories and Options21
- Canbus Data Transmission Cable22
- Cable Actuator - Electronic Motor (V)22
- Nanni Diesel - Throttle Cable for Toyota ECU23
- Nanni Diesel - Cable Only for the Inverter (Hybrid Motors)23
- Nanni Diesel - Command Cable for Throttel and Inverter (1° Part, y Cable)23
- Nanni Diesel - y Cable for Toshiba Motor Base (V) + Inverter (V)24
- Nanni Diesel - y Cable for VM Motor Base (Canbus) + Inverter24
- FPT - Throttle Canbus Command Cable25
- Cable Actuator - Gearbox Solenoid Driven25
- Nanni Diesel - Cable for Gearbox Solenoid Driven25
- FPT - Cable for Gearbox Solenoid Driven25
- Nanni Diesel - Cable for Gearbox Solenoid Drive + Neutral Signal26
- Cable Actuator - Trim/Flap26
- Nanni Diesel - Cable for the Trim/Flap Command26
- Cable Actuator - Mercruiser® Trim Pump27
- T-Splitter27
- Power Supply Connector27
- Trim/Flap Option28
7 System Types and Installation Schemes29
- Installation with 2 Mechanical Actuators - Solution a30
- Installation with 2 Mechanical Actuators - Solution B31
- Installation with 2 Mechanical Actuators - Solution C32
- Installation with 1 Actuator - Solution D33
- Installation with 1 Actuator - Solution E34
8 Configuration of the Canbus Network: End of Line Termination Resistor and Address Setting of Command Stations and Actuators35
- Configuration of the Command Station35
- Configuration of the Actuator36
9 Push-Pull Cables Installation38
- Connection Kit38
- Standard Push-Pull Cable (E2, E3, Volvo®, C0, C3, C3338
- Push-Pull Cable Outgoing from the Mercruiser® Stern Driver39
- Johnson® Push-Pull Cable39
10 Electrical Installation40
- Wiring of Actuator Output Cables40
- Cabling of the Supply Connector40
- Electrical Installation of Systems with 1 Motor, 1 Actuator and 1 Dashboard42
- Electrical Installation of Systems with 2 Motors, 1 or 2 Actuators and 2 Dashboards43
- Electrical Installation of Systems with 1 Motor, 1 Actuator and 2 Dashboards44
- Dimensional Criteria of the Power Cables for the Overall Installation45
- Electrical Cabling of the Outgoing Cables from the Actuator46
- Cabling of Actuators for Mechanical and Hybrid Propulsion Systems46
- Cabling of Actuators for Electronic Propulsion Systems47
- Cabling Scheme from Actuator to Gearbox, from Actuator to Trim or from Actuator to Flap47
11 Programming of the Actuator, General Guidelines48
- Programming Keypad48
- Display and Parameters48
- Actuator Parameters49
- Parameter "CC49
12 Setting of the Strokes of Push-Pull Cables50
- Setting of the Stroke of the Accelerator Cable50
- Setting of the Stroke of the Gearbox Cable51
13 Programming of the Actuator in Installations with Mechanical Motor and Gearbox52
- Mounting of the Push-Pull Cable52
- Programming of the Push-Pull Cable Strokes52
- Specific Parameters53
14 Programming of Actuators for Installations with Electronic Motor and Mechanical Gearbox54
- Programming of the Gearbox Strokes54
- Specific Parameters54
- Parameter A055
- Parameters to Configure the Voltage Output Signal for Electronic Motors56
15 Programming of Actuators for Mechanical Motors and Electronic Gearbox57
- Installation of Motor the Push-Pull Cable and Programming of Throttle Mechanical Strokes57
- Programming of the Push-Pull Cable Strokes57
- Electrical Cabling of the Gearbox57
- Specific Parameters57
16 Programming of Actuators with Electronic Motor and Electronic Gearbox58
- Electrical Wiring58
- Specific Parameters58
17 Programming of Actuators with Electronic CANBUS Motor and Mechanical Gearbox59
- Installation of the Push-Pull Cable and Programming of the Cable Stroke59
- Specific Parameters59
- Canbus Protocol59
- Setting of the Canbus Parameter Values60
- Technical Data of the Canbus Interface Card61
- Wiring of the Outgoing Actuator Cables61
- Connection to FPT Motors through Canbus Interface61
18 Programming of Actuators with Electronic CANBUS Motor and Electronic Gearbox63
- Canbus Motor Parameters63
- Electronic Gearbox Parameters63
- Wiring of the Actuator Outgoing Cables63
19 Programming of Actuators for Installations with Trim or Flap Command Option63
20 Programming of Actuators with the Option for Hybrid Motors64
21 Behaviour of the Electronic System in Case of Failures65
- Unforeseen Motor Switching off65
- Faults in the Electrical Network65
- Protection in Case of Overload or Break of the Push-Pull Cables65
- Troubleshooting66
- LED Diagnosis on Command Station67
22 How to Start68
23 Drilling Mask69

Flexball Series 3500 - Electrical Installation of Systems with 1 Motor, 1 Actuator and 2 Dashboards

Table of Contents

Related product manuals