Name: Flexim FLUXUS F801
Brand: Flexim
Rating: 4 (1 reviews)

To Next Page

To Previous Page

FLUXUS is a registered trademark of FLEXIM GmbH.

FLEXIM GmbH

Boxberger Straße 4

12681 Berlin

Germany

Tel.: +49 (30) 936 67 660

Fax: +49 (30) 936 67 680

E-mail: flexim@flexim.de

www.flexim.com

User manual for

FLUXUS ADM 8027, F801, ADM 8127B

UMFLUXUS_F8V4-6-1EN, 2018-10-10

Subject to change without notification.

Table of Contents5
Introduction9
Regarding this Manual9
Safety Instructions9
Warranty9
Handling10
First Inspection10
General Precautions10
General Principles11
Measurement System11
Measurement Principle11
Measurement Arrangements15
Description of the Transmitter17
Fluxus Adm 802717
Fluxus F801, Adm 8127B17
Keyboard18
Selection of the Measuring Point19
Acoustic Penetration19
Undisturbed Flow Profile21
Selection of the Measurement Arrangement Taking into Account the Measuring Range and the Measuring Conditions23
Selection of the Sound Beam Plane Near an Elbow24
Installation of FLUXUS ADM 802725
Location25
Opening and Closing the Housing25
Installation25
Connection of the Transmitter25
Connection of the Transducers27
Connection of the Power Supply31
Connection of the Outputs32
Connection of the Serial Interface36
Sensor Module (SENSPROM)36
Installation of FLUXUS F80137
Location37
Opening and Closing the Housing37
Installation37
Connection of the Transmitter37
Connection of the Transducers39
Connection of the Power Supply43
Connection of the Outputs44
Connection of the Serial Interface47
Sensor Module (SENSPROM)48
Installation of FLUXUS ADM 8127B49
Location49
Opening and Closing the Housing49
Installation49
Connection of the Transmitter50
Connection of the Transducers for Mines50
Connection of the Power Supply53
Connection of the Outputs54
Sensor Module (SENSPROM)55
Mounting of the Transducers56
Preparation of the Pipe56
Orientation of the Transducers and Transducer Distance56
Transducer Mounting Fixture Variofix L56
Installation with Variofix C65
Installation of the Transducers for Mines with FLEXIM Clasps for Mines71
Start-Up of the Transmitter72
Switching on72
Initialization72
Display72
Hotcodes74
Language Selection75
Operation State Indication75
Interruption of the Power Supply75
Basic Measurement76
Input of the Pipe Parameters76
Input of the Fluid Parameters77
Other Parameters79
Selection of the Channels79
Defining the Number of Sound Paths80
Transducer Distance80
Start of the Measurement82
Detection of the Flow Direction82
Stopping the Measurement82
Displaying the Measured Values83
Selection of the Physical Quantity and of the Unit of Measurement83
Toggling between the Channels83
Adjustment of the Display84
Status Line85
Transducer Distance85
Advanced Measuring Functions86
Command Execution During Measurement86
Damping Factor86
Totalizer86
Settings of the Hybridtrek Mode88
Upper Limit of the Flow Velocity89
Cut-Off Flow89
Uncorrected Flow Velocity90
Measurement of High Dynamic Flows (Fastfood Mode)90
Calculation Channels91
Change of the Limit for the Inner Pipe Diameter93
Diagnosis with by Means of the Snap Function94
Program Code94
Data Logger and Transmission of Data96
Data Logger96
Transmission of Data99
Libraries105
Partitioning of the Coefficient Memory105
Input of Material/Fluid Parameters Without the Extended Library106
Extended Library107
Deleting a User Defined Material/Fluids109
Arrangement of the Material/Fluid Scroll List109
Settings111
Time and Date111
Dialogs and Menus111
Measurement Settings114
Setting the Contrast115
Instrument Information115
Superuser-Modus116
Activation/Deactivation116
Transducer Parameters116
Defining Flow Parameters116
Limit of the Signal Amplification118
Upper Limit of the Sound Speed118
Detection of Long Measurement Failures119
Number of Decimal Places of the Totalizers119
Manual Reset of the Totalizers119
Display of the Sum of the Totalizers120
Display of the Last Valid Measured Value120
Display During the Measurement120
Outputs121
Installation of an Output121
Error Value Delay124
Activation of an Analog Output125
Configuration of a Frequency Output as a Pulse Output126
Activation of a Binary Output as a Pulse Output126
Activation of a Binary Output as an Alarm Output127
Behavior of the Alarm Outputs129
Deactivation of the Outputs131
Troubleshooting132
Problems with the Measurement132
Selection of the Measuring Point133
Maximum Acoustic Contact133
Application Specific Problems133
Large Deviations of the Measured Values134
Problems with the Totalizers134
Transmission of Data134
A Menu Structure135
B Units of Measurement149
C Reference154
D Maintenance158
E System Design in Accordance with Ibexu07Atex1061160

Flexim FLUXUS F801 User Manual

Table of Contents

Questions and Answers:

Flexim FLUXUS F801 Specifications

Related product manuals

Brand	Flexim
Model	FLUXUS F801
Category	Measuring Instruments
Language	English