Table of Contents
Accutronix MX Maintenance & Spare Parts Manual 130-12000 Revision B • November 2002
4.6.1 Removing Top-Mounted Handwheel 4-27
4.6.2 Installing Side-Mounted Handwheel 4-28
4.7 Thrust Base Type A1/A1E 4-30
4.7.1 Removal 4-34
4.7.2 Remounting 4-34
4.8 Torque Base Type B1 4-35
4.8.1 Removal 4-36
4.8.2 Remounting 4-36
4.9 Baseplate Type B4 (MX-05, 10, 20, & 40) 4-37
4.9.1 Removal 4-38
4.9.2 Remounting 4-38
4.10 Worm Shaft (MX-05, 10, 20, 40, 85 & 140) 4-39
4.10.1 Removal 4-40
4.10.2 Remounting 4-40
4.11 Drive Sleeve (MX-05 & 10) 4-42
4.11.1 Removal 4-43
4.11.2 Remounting 4-43
4.12 Drive Sleeve (MX-20 40, 85 & 140) 4-44
4.12.1 Removal 4-45
4.12.2 Remounting 4-46
4.12.a MX-85 & 140 Optional Drive Sleeve and Baseplate Removal 4-47
4.12.b MX-85 & 140 Optional Drive Sleeve and Baseplate Remounting 4-48
4.13 Handwheel Adapter (MX-05) 4-49
4.13.1 Removal 4-50
4.13.2 Remounting 4-51
4.14 Handwheel Adapter/Handwheel Worm Gear (MX-10, 20, 40, 85 & 140) 4-53
4.14.1 Removal 4-55
4.14.2 Remounting 4-56
4.15 Clutch & Clutch Ring Components (MX-20 & 40) 4-59
4.15.1 Removal 4-60
4.15.2 Remounting 4-61
5 Electronic Assemblies 5-1
5.1 Accutronix Control Panel (ACP) (MX-05, 10, 20, & 40) 5-1
5.1.1 Removal 5-2
5.1.2 Remounting 5-3
5.2 Control Module (MX-05, 10, 20, & 40) 5-4
5.2.1 Removal 5-5
5.2.2 Remounting 5-8
5.2.3 Fuse Replacement 5-12
5.2.4 Control Module Return Options 5-12
5.2.5 EPROM Care & Replacement 5-14
5.2.5.1 EPROM Storage & Handling 5-16
5.2.5.2 EPROM Removal 5-16
5.2.5.3 EPROM Installation 5-16
5.2.5.4 Adding Electronic Option to Your Accutronic MX Actuator 5-17
5.3 Restoring Power to Actuator with New Control Module 5-18
5.4 Terminal Block (MX-05, 10, 20, & 40) 5-18
5.4.1 Removal 5-19
5.4.2 Remounting 5-21
5.5 Control Module—Contactor Module (MX-05, 10, 20, & 40) 5-23
5.5.1 Removal 5-24
5.5.2 Remounting 5-25
5.6 Encoder (MX-05, 10, 20, & 40) 5-27
5.6.1 Removal 5-28
5.6.2 Remounting 5-29
5.7 Encoder Drive Cartridge (MX-05, 10, 20, & 40) 5-30
VI
Flow Control Division
Limitorque Actuation Systems