GE Precision 500D

om 5184516-100 Rev. 5 11-7
4-1Power Line Requirements
TABLE 11-10
MINIMUM WIRE SIZE (65 KW)
TABLE 11-11
KVA LOAD CHARACTERISTICS 65KW
TABLE 11-12
MINIMUM WIRE SIZE (80 KW)
PARAMETER THREE PHASE GENERATOR – 65 KW
Input Voltage 380VAC 400 VAC 415 VAC 440 VAC 460 VAC 480 VAC
Wire Size
Length
15 m (50 ft.)
30 m (100 ft.)
46 m (150 ft.)
60 m (200 ft.)
16 mm2
22 mm2
30 mm2
44 mm2
(#6
AWG)
(#5
AWG)
(#3
AWG)
(#1
AWG)
16 mm2
22 mm2
30 mm2
44 mm2
(#6
AWG)
(#5
AWG)
(#3
AWG)
(#1
AWG)
16 mm2
22 mm2
30 mm2
44 mm2
(#6
AWG)
(#5
AWG)
(#3
AWG)
(#1
AWG)
16 mm2
22 mm2
30 mm2
44 mm2
(#6
AWG)
(#5
AWG)
(#3
AWG)
(#1
AWG)
16 mm2
22 mm2
30 mm2
44 mm2
(#6
AWG)
(#5
AWG)
(#3
AWG)
(#1
AWG)
16 mm2
22 mm2
30 mm2
44 mm2
(#6
AWG)
(#5
AWG)
(#3
AWG)
(#1
AWG)
Phase 3 3 3 3 3 3
Nominal line Voltage (Vac) 380 400 420 440 460 480
Voltage Range (Vac) +/–10% +/–10% +/–10% +/–10% +/–10% +/–10%
Momentary Line Current (Amp) 147 140 133 127 122 117
Continuous Line Current (Amp) 7 6.7 6.2 6 5. 7 5.5
Power demands (kVA) 97 97 97 97 97 97
Frequency 47 / 53Hz and 57/63Hz
PARAMETER THREE PHASE GENERATOR – 80 KW
Input Voltage 380VAC 400 VAC 415 VAC 440 VAC 460 VAC 480 VAC
Wire Size
Length
15 m (50 ft.)
30 m (100 ft.)
46 m (150 ft.)
60 m (200 ft.)
22 mm2
30 mm2
43 mm2
54 mm2
(#5
AWG)
(#3
AWG)
(#1
AWG)
(#0
AWG)
22 mm2
30 mm2
43 mm2
54 mm2
(#5
AWG)
(#3
AWG)
(#1
AWG)
(#0
AWG)
22 mm2
30 mm2
43 mm2
54 mm2
(#5
AWG)
(#3
AWG)
(#1
AWG)
(#0
AWG)
22 mm2
30 mm2
43 mm2
54 mm2
(#5
AWG)
(#3
AWG)
(#1
AWG)
(#0
AWG)
22 mm2
30 mm2
43 mm2
54 mm2
(#5
AWG)
(#3
AWG)
(#1
AWG)
(#0
AWG)
22 mm2
30 mm2
43 mm2
54 mm2
(#5
AWG)
(#3
AWG)
(#1
AWG)
(#0
AWG)
FOR TRAINING PURPOSES ONLY!
NOTE: Once downloaded, this document is UNCONTROLLED, and therefore may not be the latest revision. Always confirm revision status against a validated source (ie CDL).