165
Detail program description - Wing mixers
the elevator joystick to its center position, so that
the marker frame surrounds both value fi elds. To
confi gure asymmetric values, move the joystick to
the corresponding side.
Values in the range -150 % to +150 % are possible,
so as to adjust the function to the direction of servo
rotation or direction of fl ap defl ection.
A simultaneous tap on the cd or ef keys of the
right touch pad (CLEAR) will reset a changed value
in a given active (inverse video) fi eld back to 0 %.
The "typical" values confi gured for this mixer are
single-digit or low two-digit values.
Flaps 6 ¼ 3 elevator
Brake settings
Aileron
0%
WING MIXERS
Elevator
flaps
0%0%
–––
–––
rudder
2
3
4
6
Normal
Flaps
elevator
0%0%
–––
63
This mixer is used to set elevator (pitch-trim)
compensation when a fl ap command is given. This
typically enables you to adjust the model's airspeed
automatically when fl aps are lowered.
If you have used the »Control adjust«, page 108, to
assign Input 6 to a transmitter control or switch then
this also affects this mixer.
Depending on the position of the fl ap control, either
a symmetrical or asymmetric setting within the range
±150 % is possible.
A simultaneous tap on the cd or ef keys of the
right touch pad (CLEAR) will reset a changed value
in a given active (inverse video) fi eld back to 0 %.
If required, the mixer can be switched on or off by
assigning a switch in the right column.
The values confi gured for this mixer are typically in
the single-digit range.
Model type: "2AIL"
If you have entered "2AIL" for the "Aileron/camber
fl aps" line on the »Model type« menu (page 94),
then the "Wing mixers menu" on your transmitter will
match the following screen image:
Aileron differential
Brake settings
0%
Aileron
0%
WING MIXERS
Elevator
aileron
0%0%
–––
–––
rudder
2
3
4
5
Normal
From the fi rst line on this display screen, you can
switch to the sub-menu with a brief tap on the center
SET key of the right touch pad …
Brake settings
Note:
The "Brake settings" menu is switched "off" if: "Motor
on C1 forward / back" in the »Model type« menu
(page 94) AND the "Motor" column of the »Phase
settings« menu, (page 142) are set to "yes" for the
currently active fl ight phase. Switch the fl ight phase if
required:
Elevator curve
BRAKE SETTINGS
Normal
Crow
AILE
0%
WK2
0%
WK
0%
Diff.- reduct
Depending on the model type selected, setting
options will now be available in the "Crow" and
"Diff(erential)reduct(ion)" lines for the column
labeled "AILE". These options should be utilized by
…
… putting the transmitter control for "Brake" •
(refer to the »Model type« menu description on
page 94) – typically the C1 joystick – in its limit
position in the brake direction. Switch to the "Crow"
line, briefl y tap on the center
SET key of the right
touch pad and use the selection keys on the left
or right touch pad to set a value that moves the
aileron upwards as far as possible to brake the
model or, if you are using airbrakes as the main
braking system, the aileron should be set to elevate
only minimally to provide an extra braking effect.
Note:
To reliably prevent the servos mechanically
striking their end-stops – which draws a heavy
current – you can set an appropriate limit value
in the column labeled "– limit +" in the »Servo
adjustment« menu, page 102.
… then fi nally, moving to the "Diff. reduct" line, set a •
% value there which is greater than or equal to that
value set (or to be set) in the "Aileron differential"
line of the display screen "before" this one.
In this way, you can suppress the aileron
differential when braking, thus ensuring that you
can count on suffi cient aileron response despite
your ailerons being defl ected upwards.
From the lowest line, "Elevator curve", you can switch
to setting the "Elevator curve" mixer by briefl y tapping
the center
SET key of the right touch pad:
To Next Page
Loading...
Need help?
General
