76 Detail program description - Base setup models | Winged models
Base setup model
Model-specifi c base settings for winged aircraft models
Before programming specifi c parameters, there are
some basic settings to be made which effect the
currently active model memory.
Use the selection keys of the left or right touch pad to
select the »Basic settings, model« menu …
Model select
Servo adjustment
Stick mode
Control adjust
Dual Rate / Expo
Channel 1 curve
Switch display
Copy / Erase
Suppress codes
Suppress models
Base setup model
Model type
… then tap the center SET key of the right touch pad.
Model name
Model name
Stick mode
1
n/a
BASIC SETTINGS,MODEL
Info
n/a
n/a
Module
bind
HoTT
Change to the next screen page with a brief tap on
the
SET key of the right touch pad. This will open a
screen of characters for entry of the model's name.
A maximum of 13 characters can be used to specify
a model name.
!"#$%&’()
Model name
Graub
@ACDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
?+,–./0123456789:;¾
¢ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÖÜ
`abcdefghijklmnopqrstuvwxyz{|}~
Now the desired characters can be selected with the
selection keys of the left touch pad. Move to the next
position to select the next character with a tap on the
f selection key of the right touch pad or its center
SET key. A simultaneous tap on the cd or ef keys
of the right touch pad (CLEAR) will place a space
character at the current position.
Positioning to any character position within the entry fi eld
can be done with the ef keys of the right touch pad.
A return to the previous menu screen is accomplished
with a tap on the center
ESC key of the left touch
pad.
A model name entered in this manner will appear in
the base screen of the »Model select« menu and in
the sub-menus of the »Copy / Erase« menu item.
Info
Model name
Stick mode
1
n/a
BASIC SETTINGS,MODEL
Info
n/a
n/a
Module
bind
HoTT
Graubele
Every model can be given a supplementary note of
up to 12 characters (maximum) by following the same
procedure as already described for creating a "Model
name". This info note will appear as a supplement in
the »Model select« menu and in the sub-menus of
the »Copy / Erase« menu item.
Stick mode
“MODE 2” (Throttle at left stick)
“MODE 3” (Throttle at right stick) “MODE 4” (Throttle at left stick)
“MODE 1” (Throttle at right stick)
elev. down
elev. up
left rudder
right rudder
full throttle
idle
left aileron
right aileron
full throttle
left rudder
right rudder
idle
elev. down
elev. up
left aileron
right aileron
elev. down
elev. up
left aileron
right aileron
Motor Vollgas
idle
left rudder
right rudder
full throttle
idle
left aileron
right aileron
elev. down
elev. up
left rudder
right rudder
There are four fundamental options for assigning
the four control functions (aileron, elevator, rudder
and throttle/brake fl ap) for a winged aircraft model
to the two joysticks. Just which of these options is
chosen depends on the individual preferences of the
individual model pilot.
Use the cd selection keys of the left or right touch
pad to select the "Stick mode" line. The option fi eld
will be framed.
Model name
Stick mode
1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module
bind
HoTT
SEL
Graubele
1234g/111111
Tap on the SET key. The currently displayed stick
mode will be displayed in inverse video. Now use the
selection keys of the right touch pad to select from
among options 1 through 4.
A simultaneous tap on the cd or ef keys of the
right touch pad (CLEAR) will reset the display to stick
mode "1".
To Next Page
Loading...
Need help?
General
