Why am I experiencing time loss with my HellermannTyton Autotool 2000 CPK Tools?
If your HellermannTyton Tools are experiencing time loss, the back-up battery for the clock in the power pack has likely discharged. Change the back-up battery.
What to do if HellermannTyton Power Tool shows 'Time loss'?
If the HellermannTyton Power Tool displays 'Time loss', it indicates that the back-up battery in the power pack is dead. Replace the back-up battery and press the Reset button.
What does 'Error, binding force' mean on HellermannTyton Autotool 2000 CPK?
If your HellermannTyton Tools display shows 'Error, binding force', the specified binding force is not being achieved. Check the binding.
How to prevent loops from forming with HellermannTyton Industrial Electrical?
Loops forming during the binding process with your HellermannTyton Industrial Electrical can be caused by several factors. It may be due to an unsuitable bundle diameter, the tie advancer not being in the correct position, a faulty spring in the upper jaw, or a blocked lower jaw. Here are some possible solutions: * Use a suitable bundle diameter. * Check the position of the tie advancer. * Check upper jaw flap in upper jaw with spring. * Check lower jaw and remove any blockage.
Why does my HellermannTyton Industrial Electrical show an error, drum?
The 'Error, drum' message on your HellermannTyton Industrial Electrical indicates that the cable tie bandoleer is pulled in at an angle, or the roller lever drum is jammed or defective. To fix this, push the actuator for the bandoleer cutter to the left and open the gate. Open the two transparent service flaps at the gate. Remove any cable-tie residues. Open the roller lever drum and turn the drum to the correct position. Then, press the Reset button and close the gate. Finally, load a new cable tie bandoleer.
What causes 'Error, front cap' on HellermannTyton Industrial Electrical?
The 'Error, front cap' message on your HellermannTyton Industrial Electrical can be caused by residues of cable ties trapped behind the front cap, or the level sensor being busy. To resolve this, clean the front sensor and carefully remove any cable-tie residues.
Why is binding not possible and the cable tie shoots straight out on my HellermannTyton Industrial Electrical?
If binding is not possible and the cable tie shoots straight out on your HellermannTyton Industrial Electrical, it means that the upper jaw is blocked. To fix this, check the upper jaw and remove any blockage.
What causes 'Error, start position' on HellermannTyton Autotool 2000 CPK, and how can I fix it?
If your HellermannTyton Tools display shows 'Error, start position', it may be because the AT2000 CPK is not in the start position. Push the actuator for the bandoleer cutter to the left. Other possible solutions include opening and closing the gate, carefully removing any cable-tie residues, and pressing the Reset button.
How to troubleshoot 'Error, drum' on HellermannTyton Autotool 2000 CPK?
If your HellermannTyton Tools display shows 'Error, drum', it could be because the cable tie bandoleer is pulled in at an angle. Refer to the instructions for opening the two transparent flaps at the gate. Another possibility is that the roller lever drum is jammed or defective, in which case you should open the roller lever drum and turn the drum to the correct position.
What to do if HellermannTyton Autotool 2000 CPK display 'Error, gate'?
If your HellermannTyton Tools display shows 'Error, gate', it may be because the drum is not in the correct position. To resolve this, open the gate and turn the drum to the correct position. Alternatively, the gate may simply be open; in that case, close it.
General| Type | Autotool 2000 CPK |
|---|---|
| Application Method | Pneumatic |
| For Cable Diameter Max. | 20 mm |
| Bundling Diameter max. | 20 mm |
| Tensile Strength min. | 80 N |
| Tensioning | Automatic |
| Tension Force | Adjustable |
| Tie Width | 4.5 mm |
| Cable Tie Width | 4.5 mm |
| Material Shortcut | PA66 |
| Operating Temperature | -40°C to +85°C |
| Tool Included | Yes |
| Pack Quantity | 1 |
| Cutting Mechanism | Automatic |
| Cutting System | Flush cut |
| Power Supply | Pneumatic |
| Operating Pressure | 6 bar |
| Material | Nylon 6.6 |
To Next Page
